Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the forward stabilizer of cross-section stability

Mirage models

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Disassemble racks of the stabilizer of cross-section stability: give lock-nuts, take cups, rubber and plugs. Turn out bolts of fastening of racks.
4. Remove a reception pipe of system of production of the fulfilled gases.
5. Hang out the power unit on the winch from above. Turn out four bolts of fastening of the central beam.
6. Remove both support of assembly of the reechny mechanism of a steering drive.
7. Disconnect from the central beam the bottom lever of a suspension bracket.
8. Prop up a beam a jack, turn out fixing bolts and omit assembly, having provided necessary free space for extraction of a bar of the stabilizer of cross-section stability.
9. Give fixture and take a bar of the stabilizer of cross-section stability from under the car.


Installation

 PERFORMANCE ORDER

Pay attention to identification marking of the left and right fixing collars.

1. Installation is made upside-down.
2. Tighten bolts of fixing collars of a bar of the stabilizer of cross-section stability with effort of 22 H • m.
3. At assembly of racks of the stabilizer track, that the size of a vystupaniye of a bolt made 22 mm.
4. Lower the car on the earth and connect a negative wire to the battery.


The Galant models for 1993 вып., FWD

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Disconnect a reception pipe of system of production of the fulfilled gases from a final collector (remove sealing laying). Tie up a pipe so that it did not disturb dismantle of the stabilizer of cross-section stability.

Try not to allow peregibaniye of the flexible coupling of reception section of a final path at an angle more than in some degrees!

4. Turn out back bolts of fastening of the central beam.
5. Turn out bolts of fastening of racks of the stabilizer of cross-section stability.

On racks of spherical type in the course of an otpuskaniye самоконтрящейся nuts should be held a sharovy finger from a provorachivaniye by means of a six-sided key.

6. Turn out bolts of fixing collars of a bar of the stabilizer of cross-section stability.
7. Delay both ends of a bar back on the car, then liberate its right end from under the bottom lever of a suspension bracket. Afterwards liberate the left end of a bar from under the opposite lever. Having pulled a bar to the right, take it from under the car.
8. Estimate degree of wear of all rubber plugs, defective components replace.
9. Check a condition of a bar of the stabilizer. In case of need make replacement.


Installation

 PERFORMANCE ORDER

1. Get a bar of the stabilizer of cross-section stability on the regular place.
2. Establish collars of fastening of a bar (pay attention to identification marking). Level components, then strongly tighten fixture.
3. At a tightening of fixture of racks of spherical type use two keys. Track, that the size of a vystupaniye of a bolt over a nut made 16 ÷ 18 mm.
4. Connect a reception pipe to a final collector (do not forget to replace sealing laying). Tighten самоконтрящиеся joint nuts with demanded effort (40 H • м).
5. Connect a negative wire to the battery.


The Galant models for 1993 вып., AWD

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Disconnect a reception pipe of system of production of the fulfilled gases from a final collector (remove sealing laying).
3. Remove the central knitsa and assembly of a transfer case.
4. Remove a rack of the stabilizer of cross-section stability, - at an otdavaniye of nuts spherical hairpins of hinges should be held from a provorachivaniye the second key.
5. Turn out a fixing bolt and remove an assembly collar of the stabilizer of cross-section stability with the rubber plug.
6. Disconnect the stabilizer from the right bottom lever of a suspension bracket.
7. Take the left section of a bar of the stabilizer through space between a power shaft and the bottom lever. The right section is taken from under the corresponding bottom lever.


Installation

 PERFORMANCE ORDER

1. Establish a stabilizer bar on the regular place.
2. Temporarily tighten fixture of an assembly collar. Level end faces of the rubber plug of adjusting labels rather put on a bar, then tighten fixture finally.
3. Screw and tighten a bolt of an assembly collar.
4. Establish racks of the stabilizer and tighten their fixing nuts, - spherical hairpins are blocked from a provorachivaniye by means of the second wrench. The bolt should act over a nut surface on mm size 16 ÷ 18).
5. Establish assembly of a transfer case and an assembly knitsa.
6. Establish the left bottom beam and tighten bolts of its fastening with demanded effort (80 H • м: back and 100 H • м: lobbies).


The Galant models since 1994 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Release самоконтрящиеся nuts and remove racks of the stabilizer of cross-section stability.

4. Remove assembly collars of a bar of the stabilizer with rubber plugs.

5. Remove the stabilizer.
6. Estimate degree of wear of components, replace the failed knots.


Installation

 PERFORMANCE ORDER

1. Get a stabilizer bar on the regular place.
2. Freely establish assembly collars.
3. Level a bar so that its both landing labels appeared at distance about 10 mm from the inside from collars.
4. Tighten bolts of fastening of collars with demanded effort (39 H • м).
5. Connect stabilizer racks to a bar and dempferny forks. Tighten lock nuts with demanded effort (39 H • м).
6. Lower the car on the earth and connect a negative wire to the battery.


Diamante models

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Remove a reception pipe of system of production of the fulfilled gases and protection of a case.
4. Remove the left and right bottom beams.
5. Remove a rack of the stabilizer of cross-section stability.
6. Release assembly collars and remove a stabilizer bar.


Installation

 PERFORMANCE ORDER

1. Get a stabilizer bar on the regular place and fix it assembly collars. Do not mix the left collar with right, - attentively study identification marking.

Before installation it is necessary to grease all rubber components of fixing knots.

2. Establish a rack of the stabilizer of cross-section stability.
3. Establish the bottom beams.
4. Establish a reception pipe of system of production of the fulfilled gases and elements of protection of a case.
5. Connect a negative wire to the battery.