Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the podrulevy combined switch

Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation. In order to avoid SRS system damage, track, that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. At the corresponding complete set of the car make safety cushion deactivation (see. Head Onboard electric equipment).
3. Remove a steering wheel (see. Section Removal and installation of a steering wheel).
4. On the Diamante models remove the handle of an otpuskaniye of the lock of a cowl.
5. Dismantle the knee emphasis located under a steering column. Remove the top and bottom sections of a casing of a steering column.
6. On the Diamante models if it is required, remove knee having blown and a sleeve of supply of air in a foot well, then accurately disconnect electroconducting from assembly of the podrulevy combined switch.
7. On the Mirage models disconnect all electroconducting, release a clamp and remove assembly of the podrulevy switch.
8. On the Galant models at the corresponding complete set turn out four screws of fastening to assembly of the podrulevy switch of a sliding contact ring темпостата. Turn out two fixing screws and remove the switch.


Installation

 PERFORMANCE ORDER

1. Establish switch assembly on the regular place and connect to it the corresponding electroconducting, - track reliability of a zashchelkivaniye of all provided clamps.
2. Establish sections of a casing of a steering column and a knee emphasis.
3. If removed, establish into place a sleeve of supply of air in a foot well and knee having blown.
4. Make sure that forward wheels of the car remain in rectilinear situation and establish into place a steering wheel (see. Section Removal and installation of a steering wheel).
5. Connect a negative wire to the battery and turn the ignition key in the situation ON, - on an instrument guard the control lamp of SRS should join for seven seconds.
6. Check serviceability of functioning of the podrulevy switch.