Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of drafts of a steering drive

Tips of steering drafts

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove the corresponding forward wheel.
3. Take шплинт and give a koronchaty nut of fastening of an external tip of steering draft on assembly of a rotary fist, - шплинты are subject to replacement without fail.

4. By means of a special stripper separate a tip from a rotary fist.

5. Mark the provision of a lock-nut concerning a tip.

6. One key holding a tip from a provorachivaniye, the second release its lock-nut, - it is necessary to give a nut on one complete revolution, no more!

7. Rotating a tip, remove it from a draft bar.


Installation

 PERFORMANCE ORDER

1. Smooth out a carving on a draft bar (a steering drive of forward wheels).
2. Screw a tip on a bar against the stop in a lock-nut, then unscrew it on one complete revolution back and tighten a nut before combination of the adjusting labels put in the course of dismantle.
3. Fill a sharovy finger of a tip in a landing nest in assembly of a rotary fist, make sure that wheels are established in rectilinear situation, screw a koronchaty nut and tighten it with demanded effort (34 H • м: the Mirage models and 29 H • м: the Galant and Diamante models). By pulling up (not an otpuskaniye) a nut achieve combination of openings under installation шплинта. Establish new шплинт, having reliably dissolved its short moustaches.
4. Establish into place a wheel. Lower the car on the earth and tighten wheel nuts with demanded effort (90 ÷ 110 H • м).
5. Connect a negative wire to the battery
6. Tighten a tip lock-nut with demanded effort (42 H • м: the Mirage models and 49 ÷ 53 H • м: the Galant and Diamante models).
7. Check corners of installation of forward wheels, in case of need make the corresponding adjustment.


Bars of steering drafts

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props.
2. Remove the corresponding forward wheel.
3. Take шплинт and give a koronchaty nut of a spherical finger of an external tip of steering draft.
4. A wire brush smooth out a carving of a bar of steering draft and moisten it with getting oil.
5. By means of a stripper liberate a tip from a rotary fist.
6. Weaken a lock-nut and remove from a bar an external tip, - count quantity of turns on which the tip was will screw.
7. Release a lock-nut of fastening of bent for to reechny transfer.
8. Release fixing collars and remove the goffered protective cover of a case of the steering mechanism.
9. Unbend uvulas of a lock plate weaken a fixing nut and disconnect the internal end of a bar from assembly of reechny transfer.


Installation

 PERFORMANCE ORDER

1. Having replaced a lock plate, establish draft and tighten it with demanded effort (90 H • м).
2. Bend uvulas of a lock plate.
3. Establish into place a protective cover and fix it new collars.
4. Establish an external tip of steering draft (see the previous subsection), - track, that the tip was will screw precisely for the quantity of turns fixed in the course of dismantle.
5. Fix a tip in a rotary fist, screw and tighten with demanded effort a koronchaty nut of a spherical finger.
6. Establish a wheel and lower the car on the earth.
7. Check corners of installation of forward wheels, in case of need make the corresponding adjustment.