Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the switch of ignition

Mirage and Galant models

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the handle of an otpuskaniye of the lock of a cowl.
3. Remove a knee emphasis.
4. Remove a sleeve of an air line and the panel of furnish of knee level.
5. Remove a steering wheel (see. Section Removal and installation of a steering wheel).
6. Remove the top and bottom section of a casing of a steering column.
7. On the Galant models insert a key into the lock of ignition and turn it in situation ASS, then the small sharp tool push in zamkovy assembly a lock pin and take the lock cylinder.

On models from AT on a wall of the zamkovy cylinder the sliding lever of a drive of blocking of a key from which it is necessary to disconnect a driving cable is established.

8. At the corresponding complete set dismantle the alarm sensor switch of extraction of the ignition key.
9. Disconnect from the ignition switch electroconducting. Turn out fixing screws and take switch assembly from the zamkovy cylinder.


Installation

 PERFORMANCE ORDER

1. On models from AT take a key and establish on the lock cylinder the sliding lever and connect to it a driving cable. Grease a cable with greasing and establish the cylinder in a casing of zamkovy assembly. Check serviceability of functioning of a blokirator.
2. Fill the ignition switch in a back part of a casing of zamkovy assembly, - track correctness of combination of wells.
3. Connect electroconducting and establish a clamp.
4. Establish casings of a steering column.
5. Establish a steering wheel and a knee emphasis.
6. Establish the handle of an otpuskaniye of the lock of a cowl.
7. Connect a negative wire to the battery, activate a safety cushion and check serviceability of functioning of the switch of ignition.


Diamante models

Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Deaktiviruyte a safety cushion (see. Head Onboard electric equipment).
3. Remove a steering wheel (see. Section Removal and installation of a steering wheel).
4. Remove the handle of an otpuskaniye of the lock of a cowl.
5. Remove located on the panel of a knee emphasis under a steering column switches, turn out the opened screws and dismantle an emphasis.
6. Remove the top and bottom sections of a casing of a steering column, - try not to break off directing uvulas.
7. If it is required, remove a sleeve of supply of air in a foot well, then accurately disconnect electroconducting from the ignition switch.
8. Turn out fixing screws and liberate the switch from the zamkovy cylinder.

Installation

 PERFORMANCE ORDER

1. Fill the switch in a casing of zamkovy assembly, - track correctness of combination of wells. Screw and tighten fixing screws.
2. Connect to the switch electroconducting.
3. Establish knee having blown and an air line sleeve.
4. Establish a knee emphasis and the panel of switches.
5. Establish the handle of an otpuskaniye of the lock of a cowl.
6. Establish a steering wheel.
7. Establish casings of a steering column.
8. Connect a negative wire to the battery, activate a safety cushion and check serviceability of functioning of the switch of ignition.