Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the switch of management by functioning of screen wipers

On other models this switch is built in in assembly of the combined podrulevy switch and to service in an individual order on is subject.


Removal

 PERFORMANCE ORDER

1. At the corresponding complete set of the car make safety cushion deactivation for what bring forward wheels into rectilinear situation and take a key from the ignition lock (the column should be blocked). Disconnect a negative wire from the battery and wind its contact tip with a high-quality insulating tape. Wait within not less than one minute during which the safety cushion remains active in an independent mode.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove a steering wheel (see. Section Removal and installation of a steering wheel).
3. Remove the handle of an otpuskaniye of the lock of a cowl.
4. Remove located on the panel of a knee emphasis under a steering column switches, turn out the opened screws and dismantle an emphasis.
5. Remove the top and bottom sections of a casing of a steering column.
6. If it is required, remove a sleeve of supply of air in a foot well, then accurately disconnect electroconducting from assembly of the switch of management by functioning of screen wipers.
7. Turn out fixing screws and remove switch assembly from a steering column.


Installation

 PERFORMANCE ORDER

1. Establish switch assembly on the regular place and connect to it the corresponding electroconducting, - track reliability of a zashchelkivaniye of all provided clamps.
2. If removed, establish into place a sleeve of supply of air in a foot well.
3. Establish sections of a casing of a steering column and a knee emphasis.
4. Establish the handle of an otpuskaniye of the lock of a cowl.
5. Make sure that forward wheels of the car remain in rectilinear situation and establish into place a steering wheel (see. Section Removal and installation of a steering wheel).
6. Connect a negative wire to the battery and turn the ignition key in the situation ON, - on an instrument guard the control lamp of SRS should join for seven seconds.
7. Check serviceability of functioning of the switch.