Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Corners of installation of wheels

Disorder of wheels

And — the Cylinder will slide on a straight line
In — the Cone will slide on a circle with the center from the narrow end
With — the Scheme of contact of wheels with a paving

D — Positive disorder
Е — the Vertical plane


General information

Corners of installation of wheels define geometry of provision of the last concerning a car and paving suspension bracket. Violation of adjustment of this geometry conducts to decrease in controllability of the car and increase of speed of wear of tires. Into number of subjects to control of corners of installation of forward wheels of the car enter disorder, выбег (a corner of a longitudinal inclination of an axis of turn of a wheel) and convergence (see below).

Adjustment of geometry of a suspension bracket demands use of the special expensive and bulky equipment and it is necessary to charge its performance to specialists of car-care center.

Convergence

The data size to each other forward edges of wheels of the car is called as convergence. Such violation of parallelism of installation of wheels allows to minimize wear of a protector for the account юза at commission of turns. At zero convergence distance between forward edges of wheels equally to distance between their back edges. Normal convergence usually does not exceed inch shares (1 inch = 2.54 cm). Violation of adjustment of convergence conducts to acceleration of wear of protectors of tires at the expense of a proskalzyvaniye them on a paving.

 


Disorder

The tilt angle of the plane of wheels concerning a vertical is called as disorder. If wheels are inclined by the upper edges outside, disorder is called as positive, and on the contrary. The size of disorder is measured in degrees. Correctness of adjustment of disorder defines size and the provision of a spot of contact of protectors with the road and allows to compensate changes in suspension bracket geometry during commission of turns and at car movement on a rough paving. Small negative disorder allows to increase a spot of contact of a protector during commission of turns, however, being excessive, leads to violation of course stability of the car and strengthening of the breakthroughs transferred to a steering wheel.

Выбег

Vybegom is called a corner of a longitudinal inclination of an axis of turn of a wheel, i.e., a deviation corner from a vertical of an axis of turn of a wheel in the plane of the last. If the axis of turn is inclined back, выбег is called as positive, on the contrary. Positive выбег provides self-return of forward wheels to rectilinear situation at an exit from turn, increasing thereby course stability of a vehicle, however, being excessive, reduces maneuverability of the car.

 Lowering of a back of the car leads to increase positive выбега wheels.