Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Regenerative repair of rack-mount assemblies of a forward suspension bracket

Design of a rack of Mac-Fersona

1 — the Rack
2 — the Boot of an amortization rod
3 — the Screw spring (it is compressed by means of the special tool)
4 — the Washer of the top saddle of a spring
5 — Assembly of the top support of a rack
6 — the Washer of the top nut
7 — the Nut of fastening of the top support

The models Diamante, Galant (on 1993 and since 1999 вып.) and Mirage

Dismantling

 PERFORMANCE ORDER

1. The design of rack-mount assembly on the listed models is shown on an illustration.
2. Remove rack-mount assembly from the car (see. Section Removal and installation of racks and screw springs of a forward suspension bracket).
3. By means of the special tool compress a screw spring.

4. Having pressed a rack to the top cover, compress it approximately on 1/2 courses of an amortization rod, - at all up to the end!
5. Give the central nut and remove assembly of the top support and the top saddle of a spring.

6. Remove a screw spring.


Assembly

 PERFORMANCE ORDER

1. Establish on rack-mount assembly the compressed screw spring.
2. Establish assembly of the top support and tighten a nut of its fastening with demanded effort (59 H • м).
3. Release the tool compressing a spring.
4. Establish rack-mount assembly on the car (see. Section Removal and installation of racks and screw springs of a forward suspension bracket).


Galant 1994 ÷ 1998 models of вып.

Dismantling

 PERFORMANCE ORDER

1. Remove shock-absorber assembly with a screw spring (see. Section Removal and installation of racks and screw springs of a forward suspension bracket).
2. Compress a spring by means of the special tool.
3. Release самоконтрящуюся a nut and remove the washer enclosed under it. Remove the plug, assembly of the top support, and also a spring saddle with a slip.


Installation

 PERFORMANCE ORDER

1. Establish on shock-absorber assembly the screw spring compressed by means of the special tool, - track, that the prutok of a spring rested an end face against special sample in a saddle.
2. Establish a boot, a rubber pillow, a cup, the top plug and a saddle with a slip.
3. Tighten fixture, release a spring and establish assembly on the car (see. Section Removal and installation of racks and screw springs of a forward suspension bracket).