Mitsubishi Galant

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Remove a brake drum/disk (see. Head Brake system).
3. Remove nave assembly with the wheel bearing (see. Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom support of the shock-absorber.
6. Disconnect the longitudinal lever from a beam of the back bridge.
7. Turn out a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Get assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with demanded effort (100 ÷ 120 H • м).
2. Connect the lever to a beam of the back bridge. Tighten a fixing bolt with effort of 100 ÷ 120 H • m.
3. Fix on the lever the bottom support of the shock-absorber, - tighten fixing with effort of 80 ÷ 100 H • м).
4. Clean propping up a beam of the back bridge a jack.
5. Establish into place stupichny assembly.
6. Establish a brake drum/disk (see. Head Brake system).
7. Establish a wheel and lower the car on the earth.

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Remove a brake drum/disk (see. Head Brake system).
3. Remove nave assembly with the wheel bearing (see. Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom operating lever of a suspension bracket.
6. Disconnect from the lever the top coupler.
7. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Get assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with demanded effort (100 ÷ 120 H • м).
2. Connect to the lever the top coupler, tighten a fixing boat with effort of 90 H • m.
3. Connect to the longitudinal lever the bottom operating lever, tighten a fixing bolt with effort of 90 H • m.
4. Clean propping up a beam of the back bridge a jack.
5. Establish into place stupichny assembly.
6. Establish a brake drum/disk (see. Head Brake system).
7. Establish a wheel and lower the car on the earth.

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Prop up a jack a beam of the back bridge.
3. Disconnect the longitudinal lever from a fist of stupichny assembly.
4. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Get assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with demanded effort (137 ÷ 157 H • м).
2. Connect the lever to a fist of stupichny assembly, tighten a fixing bolt with effort of 118 ÷ 137 H • m.
3. Clean propping up a beam of the back bridge a jack.
4. Establish a wheel and lower the car on the earth.

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Remove a brake drum/disk (see. Head Brake system).
3. Remove stupichny assembly (see. Section Removal and installation of stupichny assemblies).
4. Prop up a jack a beam of the back bridge.
5. Disconnect from the longitudinal lever the bottom support of the shock-absorber.
6. Disconnect from the lever a rack of the stabilizer of cross-section stability.
7. Disconnect from the lever a tip of cross-section draft.
8. Disconnect from the longitudinal lever the bottom operating lever of a suspension bracket.
9. Give a through bolt of fastening of the longitudinal lever to a body element and remove lever assembly from the car.

1. Get assembly of the longitudinal lever on the regular place and establish a through bolt of fastening it on a body. Tighten a bolt nut with demanded effort (140 ÷ 160 H • м).
2. Connect to lever assembly the bottom operating lever of a suspension bracket, tighten a fixing bolt with demanded effort (140 ÷ 160 H • м).
3. Connect to the lever a tip of cross-section draft. Tighten a fixing nut with effort of 29 H • m.
4. Establish on the lever a rack of the stabilizer of cross-section stability, tighten fixing to a hook with effort of 40 H • m.
5. Connect to the lever the shock-absorber. Tighten a fixing bolt with demanded effort (90 H • м).
6. Clean propping up a beam of the back bridge a jack.
7. Establish into place stupichny assembly.
8. Establish a brake drum/disk.
9. Establish a wheel and lower the car on the earth.