Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the cylinder of the lock of ignition

Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.


Removal

 PERFORMANCE ORDER

1. At the corresponding complete set of the car make safety cushion deactivation (see. Head Onboard electric equipment).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. Remove from the bottom finishing section the handle of an otpuskaniye of the lock of a cowl.
4. Remove a knee emphasis.
5. Remove an air sleeve of knee level and dismantle a steering wheel (see. Section Removal and installation of a steering wheel).
6. Remove the top and bottom sections of a casing of a steering column.
7. On the Diamante models remove knee having blown and a sleeve of supply of air in a foot well.
8. In case of need liberate an electroconducting plait from intermediate clamps on a steering column.
9. Disunite the corresponding contact sockets.
10. On the Galant and Diamante models turn out fixing screws and remove on the left side of a steering column podrulevy the switch (assembled with a contact spring of a safety cushion - the models equipped with SRS).
11. On the Diamante models turn out fixing screws and take the switch of ignition of the cylinder of zamkovy assembly.
12. Insert a key into the cylinder of the lock of ignition and turn it in situation ASS.
13. The suitable sharp tool push inside a lock pin in the cylinder of the lock of blocking of a steering column and take the zamkovy cylinder outside.
14. At the corresponding complete set dismantle the alarm sensor switch of extraction of the ignition key.


Installation

 PERFORMANCE ORDER

1. On the Mirage models establish the lock cylinder on the basic arm.

If arm replacement was made, before an oblamyvaniye of heads of srezny locks make sure of serviceability of functioning of the cylinder.

2. On the Galant and Diamante models establish the cylinder in a casing of zamkovy assembly, - track reliability of a zashchelkivaniye of clamps. Fill in a casing the ignition switch, achieve combination of zamkovy wells and screw fixing screws.
3. On the Galant and Diamante models establish into place assembly of the podrulevy switch with the contact SRS reel, restore initial connection of electroconducting.
4. At the corresponding complete set establish the alarm sensor switch of extraction of a key.
5. Connect electroconducting and establish a clamp.
6. If removed, establish into place knee having blown and an air line sleeve.
7. Establish casings of a steering column.
8. Establish a steering wheel and a knee emphasis.
9. Establish the handle of an otpuskaniye of the lock of a cowl.
10. Connect a negative wire to the battery, activate a safety cushion and check serviceability of functioning of the switch of ignition.