Mitsubishi Galant

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove both back wheels.
3. Prop up the bottom lever of a suspension bracket a jack.
4. Mark the adjusting provision of the top plate of a screw spring.
5. On models with an active suspension bracket (Active-ECS) release a nut of fastening of an air-line to the top part of a rack. A sealing ring will throw out, - it is subject to replacement without fail. Turn out fixing bolts and remove from the top part of a rack the Active-ECS actuation mechanism, - do not forget to disconnect electroconducting.
6. Turn out a bolt of the bottom support of the shock-absorber. Give nuts of fastening of the top plate of the shock-absorber to a body element.
7. Lower propping-up bottom lever a jack, remove a rack and take it from under the car.

1. Fill the top plate of a screw spring on the regular place and establish a rack on the car, - use a jack.
2. Tighten the top fixing nuts with demanded effort (45 H • м).
3. The bottom bolt tighten with effort of 98 H • m.
4. On models with Active-ECS connect е to a rack an air-line, - do not forget to replace a sealing ring. Tighten a shtutserny nut with demanded effort (9 H • м).
5. Establish on a rack the Active-ECS actuation mechanism, connect to it electroconducting and fix bolts.
6. Clean a jack, establish wheels and lower the car on the earth.
7. Connect a negative wire to the battery.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Slightly prop up a torsionny beam and the lever, - track, that the jack did not concern a cross-section jet bar.

Between a head of a jack and a beam of the bridge it is necessary to lay surely wooden whetstone, get a jack under the central part of a beam.

4. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of a luggage compartment.
5. On models with an active suspension bracket (Active-ECS) mark and disconnect from the top part of the shock-absorber air-lines. At once закупорьте the open ends of tubes and unions in order to avoid hit in dirt system. Try not to allow perekruchivaniye and peregibaniye of tubes. Remove a sealing ring and the plug. Remove assembly of the actuation mechanism.
6. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
7. Turn out the bottom fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. To Poddomkratta a beam of the back bridge, achieving hit of fixing hairpins of the top support of the shock-absorber in reception openings. Fix a rack in the top situation.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (40 H • м).
4. Lower the car on the earth and finally tighten the bottom bolt of fastening of the shock-absorber with demanded effort (100 H • м).
5. On models with an active suspension bracket establish into place the Active-ECS components and restore initial connection of air-lines, - do not forget to replace sealing rings. Tighten a lock-nut with effort of 9 H • m. Moisten the shtutserny socket with soap water, start the engine and check connection on existence of signs of leakages of air. In case of need replace a sealing ring.
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage compartment.

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Slightly prop up a jack the longitudinal lever of a suspension bracket.
4. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of a luggage compartment.
5. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
6. Give a bolt of fastening of a basic arm of a brake hose.
7. Turn out the bottom fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. To Poddomkratta the longitudinal lever, achieving hit of fixing hairpins of the top support of the shock-absorber in reception openings. Fix a rack in the top situation.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (40 H • м).
4. Lower the car on the earth and finally tighten the bottom bolt of fastening of the shock-absorber with demanded effort (90 ÷ 110 H • м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with demanded effort (17 H • м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage compartment.

1. To Poddomkratta the car also establish it on props.
2. Slightly prop up a jack the bottom operating lever of a suspension bracket.
3. For the purpose of ensuring access to the top fixing nuts delay outside a stopper of a back seat, lift and remove a pillow. Turn out fixing bolts and remove a seat back.

4. Give the top nuts of fastening of the shock-absorber.

5. Turn out the bottom fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. To Poddomkratta a beam of the back bridge, achieving hit of fixing hairpins of the top support of the shock-absorber in reception openings. Fix a rack in the top situation.
3. Screw on hairpins of a nut and tighten them with demanded effort (44 H • м).
4. Lower the car on the earth and finally tighten the bottom bolt of fastening of the shock-absorber with demanded effort (98 H • м).
5. Establish into place components of a back seat.

1. For the purpose of ensuring access to the top fixing nuts remove the corresponding elements of an upholstery of a luggage compartment.
2. Remove a protective cover and give the top nuts of fastening of the shock-absorber.
3. To Poddomkratta the car also establish it on props.
4. Slightly prop up a jack the longitudinal lever of a suspension bracket.
5. Mark the adjusting provision of the top plate of a spring concerning the chassis, then give fixing nuts.
6. Turn out the bottom fixing bolt and remove rack-mount assembly from the car.

1. Get a rack on the regular place, screw and slightly tighten the bottom fixing bolt.
2. To Poddomkratta the longitudinal lever, achieving hit of fixing hairpins of the top support of the shock-absorber in reception openings. Fix a rack in the top situation.
3. Screw on hairpins fixing nuts and tighten them with demanded effort (27 H • м).
4. Lower the car on the earth and finally tighten the bottom bolt of fastening of the shock-absorber with demanded effort (90 H • м).
5. Establish a basic arm of a brake hose and tighten a bolt of its fastening with demanded effort (17 H • м).
6. Establish the top protective cover of the shock-absorber and elements of an upholstery of a luggage compartment.