Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the back stabilizer of cross-section stability

The Galant models for 1993 вып.

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props.
2. Prop up a jack a beam of the back bridge.
3. Give самоконтрящиеся fixing nuts and remove basic arms of the bottom beam.
4. Turn out fixing bolts and remove assembly collars of a bar of the stabilizer of cross-section stability.
5. Holding a stabilizer bar from a provorachivaniye a wrench, give самоконтрящуюся a nut.
6. Remove basic cups and the rubber plug.
7. A wrench block a stabilizer rack from a provorachivaniye and release самоконтрящуюся a nut of its fastening. Operating in a similar manner, disconnect the second rack.
8. Lower a jack which is propping up a beam of the back bridge, having left a small gap between a suspension bracket and a car body.
9. Take a bar of the stabilizer of cross-section stability from under the car.
10. Check a condition of a bar of the stabilizer and estimate degree of wear of components of its fastening.


Installation

 PERFORMANCE ORDER

1. Get a bar of the stabilizer of cross-section stability on the regular place and raise a jack a beam of the back bridge.
2. Connect to a bar of a rack of the stabilizer and fix their new самоконтрящимися nuts, having tightened the last with effort of 45 H • m.
3. Establish the central plugs and collars of fastening of the stabilizer. Screw fixing bolts and tighten them with demanded effort (14 H • м).
4. Return into place a cable of a drive of the parking brake, tighten an adjusting bolt of the wheel sensor.
5. Establish a basic arm of the bottom beam, tighten a fixing bolt with effort of 85 H • m, a nut - 130 H • m.
6. Establish in beam arms new rubber pillows, tighten new самоконтрящиеся nuts with demanded effort (110 ÷ 130 H • м).
7. Lower the car on the earth.


Diamante and Galant 1994 ÷ 1998 models of вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.

3. Give самоконтрящиеся nuts of fastening of racks of the stabilizer of cross-section stability.

4. Turn out bolts of fastening of assembly collars, remove rubber plugs.
5. Remove a stabilizer bar from the car.
6. Check a condition of a bar of the stabilizer and estimate degree of wear of components of its fastening.


Installation

 PERFORMANCE ORDER

1. Get a stabilizer bar on the regular place.
2. Freely fix assembly collars.
3. Achieve the correct combination of adjusting marking, - the labels put on a bar should appear at distance about 10 mm from external edges of both assembly collars.
4. Having leveled a bar in a demanded way, tighten fixing nuts with demanded effort (38 H • м).
5. Connect stabilizer racks to dempferny forks and a bar. Tighten fixing nuts with demanded effort (38 H • м).
6. Lower the car on the earth.
7. Connect a negative wire to the battery.