Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the bottom managing directors of levers of a back suspension bracket

The Galant models for 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Remove racks of the stabilizer of cross-section stability or bolts of its fastening to the bottom lever of a suspension bracket. At the corresponding complete set remove basic cups/plugs.
4. By means of a special stripper of the Mv9f35 type liberate a finger of a spherical support from a fist of stupichny assembly - if the support is subject to further use, act extremely carefully.
5. Give internal bolts and a nut of fastening of the bottom lever of a suspension bracket.
6. Turn out back bolts and, - at the corresponding complete set, - remove a fixing collar.
7. Remove the lever from the car.
8. In case of need remove the plug from a back rod.


Installation

 PERFORMANCE ORDER

1. If removed, establish on the lever the plug.
2. Get lever assembly on the regular place and fix it internal bolts. Screw and temporarily tighten a new nut.
3. Establish a back fixing collar, screw bolts. Tighten new nuts of fastening of a collar with demanded effort (47 H • м) temporarily tighten a collar bolt, - a final tightening of a bolt with demanded effort (100 H • м) are made after car lowering on the earth.
4. Press spherical in a fist of stupichny assembly and fix it a new nut, having tightened the last with effort of 60 ÷ 72 H • m.
5. Establish a bar of the stabilizer of cross-section stability with the racks.
6. Lower the car on the earth and make a final tightening of nuts of internal bolts of fastening of the lever with effort of 120 H • ми a collar bolt (100 H • м).
7. Make sure of reliability of a tightening of fixture of elements of a suspension bracket.
8. Connect a negative wire to the battery.


The Galant models since 1994 вып.

The bottom operating lever

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. On models from ABS remove from assembly of the bottom managing director of the lever basic arms of electroconducting of the wheel sensor.

3. Remove a through bolt of fastening of the bottom fist to the operating lever of stupichny assembly.

4. Remove a bolt of fastening of the bottom managing director of the lever to a suspension bracket beam.

5. Remove the lever from the car.


Installation

 PERFORMANCE ORDER

1. Connect the lever to a beam of a suspension bracket and temporarily tighten a nut of a fixing bolt.
2. Connect the lever to a fist of stupichny assembly, - also temporarily tighten to a hook of a through bolt.
3. Connect to the lever a rack of the stabilizer of cross-section stability. Tighten a fixing nut with demanded effort (39 H • м).
4. Establish a wheel and lower the car on the earth.
5. Make a final tightening of nuts of both fixing bolts with demanded effort (98 H • м).
6. Check corners of installation of back wheels, in case of need make the corresponding adjustment.


The bottom operating lever of adjustment of convergence

Removal

 PERFORMANCE ORDER

The spherical support is built in lever assembly and in case of its exit is out of operation replaced complete with the last.

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Mark the provision of an adjusting bolt.

3. By means of a stripper of the Mv991113 type liberate a finger of a spherical support from a fist of stupichny assembly.

4. Give bolts of fastening of the lever to a beam of a suspension bracket and remove lever assembly from the car.


Installation

 PERFORMANCE ORDER

1. Connect the lever to a suspension bracket beam, achieve combination of adjusting labels of an adjusting bolt, then temporarily tighten a nut of a fixing bolt.
2. Press a finger of a spherical support in a fist of stupichny assembly, tighten with demanded effort (28 H • м) a fixing nut.
3. Establish a wheel and lower the car on the earth.
4. Finally tighten with demanded effort (69 ÷ 78 H • м) boltovy pair of fastening of the lever on a suspension bracket beam
5. Check corners of installation of back wheels, in case of need make the corresponding adjustment.


Diamante models

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Mark the provision of an adjusting bolt.
3. On models with an active suspension bracket (Active-ECS) disconnect a rod of the sensor of height of a road gleam from assembly of the bottom lever.
4. Prop up the longitudinal lever of a suspension bracket a jack and thaw самоконтрящуюся a nut of fastening of the bottom lever to the longitudinal lever.
5. Disconnect lever assembly from a beam of a suspension bracket and remove it from the car.


Installation

 PERFORMANCE ORDER

1. Connect the lever to a suspension bracket beam, achieve combination of adjusting labels of an adjusting bolt, then temporarily tighten a nut of a fixing bolt.
2. Connect assembly to the longitudinal lever and tighten самоконтрящуюся a nut with demanded effort (75 ÷ 89 H • м).
3. On models with an active suspension bracket connect to the lever a rod of the sensor of height of a road gleam.
4. Establish a wheel and lower the car on the earth.
5. Finally tighten with demanded effort (75 ÷ 89 H • м) boltovy pair of fastening of the lever on a suspension bracket beam
6. Check corners of installation of back wheels, in case of need make the corresponding adjustment.