Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of the bottom levers of a forward suspension bracket

Details of installation of the bottom levers of a forward suspension bracket on the Galant 1994 ÷ 1998 models of вып.

* the Asterisk marked the fixture which final tightening should be made after car lowering on the earth
1 — the Nut of fastening of a spherical support of jet section of the bottom lever in a rotary fist
2 — the Bolt of fastening of jet section of the bottom lever
3 — Assembly of jet section of the bottom lever of a suspension bracket
4 — Arms

5 — Fixture of the bottom support of the shock-absorber
6 — the Nut of fastening of a spherical support of cross-section section of the bottom lever in a rotary fist
7 — Fixture of cross-section section of the bottom lever of a suspension bracket
8 — Assembly of cross-section section of the bottom lever of a suspension bracket


Details of installation of the bottom lever of a suspension bracket on the Mirage models

1 — the Bottom spherical support
2 — Samokontryashchayasya a nut
3 — the Rubber plug of a support of the stabilizer of cross-section stability
4 — the Bar of the stabilizer of cross-section stability
5 — the Metal plug
6 — Fixture of a forward support of the bottom lever
7 — the Collar

8 — Assembly of the bottom lever

* the Asterisk marked the fixture which final tightening should be made after car lowering on the earth


The Diamante and Galant models on 1993 and since 1999 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props, - wheels should appear completely torn off from the earth.
3. Disconnect from the bottom lever a rack of the stabilizer of cross-section stability.
4. Liberate a finger of the bottom spherical support from assembly of a rotary fist.
5. Give a fixing nut and take a through bolt of fastening of an internal support of the lever to a frame.
6. Turn out back fixing bolts, at the corresponding complete set remove a collar.
7. In case of need remove the plug of a back rod.


Installation

 PERFORMANCE ORDER

1. If removed, establish on assembly of the bottom lever the plug of a back rod.
2. Establish lever assembly on the car and temporarily tighten a nut of a through bolt.
3. Establish a collar, bolts and replaceable nuts of a back support. Tighten bolts with effort of 100 ÷ 120 H • m, nuts - 40 H • m.
4. Fill a finger of a spherical support in assembly of a rotary fist and tighten a new fixing nut with demanded effort (60 ÷ 72 H • м).
5. Connect to the lever a rack of the stabilizer of cross-section stability.
6. Lower the car on the earth for a final tightening of fixture.
7. After all mass of the car will be transferred on a suspension bracket tighten nuts of through bolts of the bottom levers of a suspension bracket with demanded effort (102 ÷ 122 H • м).
8. Connect a negative wire to the battery.
9. Execute check and adjustment of corners of installation of forward wheels.


Galant 1994 ÷ 1998 models of вып.

Removal

 PERFORMANCE ORDER

1. Details of installation of the bottom levers of a suspension bracket on the Galant 1994 ÷ 1998 models of вып. are shown on an accompanying illustration. Both spherical support are built in in bodies of the sections of the bottom lever and in case of their exit out of operation are subject to replacement assembled with the last.
2. To Poddomkratta the car also establish it on props.

3. Give a nut of a bolt of fastening to cross-section section of the bottom lever of a dempferny fork of the shock-absorber, take a bolt. Liberate fingers of the bottom spherical support from a rotary fist.

4. For removal of cross-section section of the lever it is necessary to dismantle arms of the bottom beam previously.
5. Give fixture of the internal end of cross-section section of the bottom lever and remove assembly of the last from the car.
6. Turn out two fixing bolts and remove jet section of the bottom lever.


Installation

 PERFORMANCE ORDER

1. Plant in assemblies of sections of the bottom lever rubber plugs.
2. Establish cross-section section of the bottom lever of a suspension bracket on the regular place. Fill an internal fixing bolt and temporarily tighten a new nut of its fastening.
3. Establish jet section of the lever.
4. Fill fingers of both spherical support in assembly of a rotary fist. Screw new fixing nuts and tighten them with demanded effort (59 ÷ 71 H • м).
5. Lower the car on the earth and finally tighten the corresponding fixture of cross-section section with demanded effort (98 ÷ 118 H • м: an internal bolt and 88 H • м: a bolt of fastening of a dempferny fork).
6. With demanded effort (83 H • м) tighten bolts of fastening of jet section.
7. Establish into place arms of the bottom beam and tighten bolts of their fastening with effort of 69 ÷ 78 H • m.
8. Make adjustment of corners of installation of forward wheels.


Mirage models

Removal

 PERFORMANCE ORDER

1. Details of installation of assembly of the bottom lever of a suspension bracket on the Mirage models are shown on an illustration.
2. To Poddomkratta the car also establish it on props. Remove the corresponding forward wheel.
3. Remove from assembly of the bottom lever of a suspension bracket of a rack of the stabilizer of cross-section stability, or give nuts and take fixing bolts. Remove cups and plugs of connecting knots.
4. Liberate from a rotary fist a finger of a spherical support.
5. Give a nut and take an internal bolt of fastening of assembly of the bottom lever.
6. Turn out bolts of a back fixing collar and remove assembly of the bottom support from the car.


Installation

 PERFORMANCE ORDER

1. Establish assembly of the bottom lever on the regular place and tighten a nut of an internal fixing bolt with demanded effort (108 H • м).
2. Establish a back fixing collar and tighten bolts of its fastening with effort of 90 H • m.
3. Fill a finger of a spherical support in assembly of a rotary fist. Screw a new nut and tighten it with effort of 60 ÷ 72 H • m.
4. Fix on lever assembly a rack of the stabilizer of cross-section stability.
5. Lower the car on the earth and finally tighten fixture with demanded effort.
6. Establish a wheel.