Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Get lost in captivating storylines and compelling characters on Soap2day.

Air removal from a hydraulic path of system of strengthening of a wheel

Forward steering drive

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props.
2. Several times manually turn a pulley of the steering pump.
3. Five-six times turn a steering wheel from an emphasis against the stop.
4. Disconnect VV a wire of system of ignition and, short breakthroughs turning a starter, within 15 ÷ 20 seconds five-six times turn a steering wheel from an emphasis against the stop, - during pumping watch, that hydraulic liquid in the tank of the steering pump did not fall below level of an arrangement of the filter. If to carry out pumping at the working engine, air present at a path will be adsorbed in liquid, - make pumping only by a provorachivaniye of not started engine.
5. Restore initial connection of VV of a wire, start the engine and let's to it work for some time on single turns.
6. Rotating a steering wheel, make sure of absence of emergence of air bubbles in the pump tank.
7. Check level and a condition of hydraulic liquid, - it should not have a dairy and figurative consistence.
8. Make sure that rotation of a steering wheel does not render appreciable influence on liquid level in the tank, - if the size of change makes more than 5 mm, repeat pumping procedure.


Back steering drive

 PERFORMANCE ORDER

1. Pump over a forward steering drive (see above).
2. Start the engine and leave it working at single turns.
3. Weaken the pumping gate at the left on klapanny assembly of management. Connect to the gate the special tool for pumping of a hydraulic path (МВ991230).
4. Turn a steering wheel against the stop to the left, then at once return it to rectilinear situation. Make sure of serviceability of an exit from a path of air bubbles.
5. Repeating the actions described in the previous paragraph, achieve complete removal of air from a hydraulic contour, then muffle the engine.
6. Weaken on 1/8 turns the gate of pumping of the strengthening cylinder of the back steering mechanism and connect to it the tool for pumping, - the nozzle is equipped with the special emphasis limiting extent of opening of the gate.
7. Start the engine and make on the car a short trip at about 80 km/h, having provided with that circulation of hydraulic liquid in a path of a back steering drive.
8. Moving with a speed about 32 km/h, it is active повращайте a steering wheel, - the remains of air should be removed from a path in reception capacity of a set for pumping.
9. Continue procedure before complete removal of air from system.