Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Regenerative repair of rack-mount assemblies of a back suspension bracket

Design of rack-mount assembly of a back suspension bracket of the Mirage and Galant models since 1994 вып.

1 — the Protective cover
2 — Samokontryashchayasya a nut
3 — the Washer
4 — the Top plug A
5 — the Top saddle of a spring
6 — the Overlay of a saddle of a spring
7 — the Top plug B

8 — the Metal plug
9 — the Cup
10 — the Boot
11 — the Limiter of a course of compression
12 — the Screw spring
13 — the Shock-absorber
N — Replace


The Mirage and Galant models since 1994 вып.

Dismantling

 PERFORMANCE ORDER

1. The design of rack-mount assembly of a back suspension bracket of the Galant and Mirage models is shown on an illustration.
2. Remove rack-mount assembly from the car (see. Section Removal and installation of back racks).
3. The special tool compress a screw spring.
4. Remove a protective cover.
5. Holding a shock-absorber rod from a provorachivaniye, give самоконтрящуюся a nut.
6. Remove assembly of the top saddle of a spring with a slip.
7. Remove the metal plug, plugs A and B, a cup, the limiter of a course of compression and a dustproof casing.
8. Remove from the shock-absorber the compressed screw spring.


Installation

 PERFORMANCE ORDER

1. Establish the compressed screw spring on the shock-absorber, - achieve end face hit a prutka of an extreme round of a spring in deepening in an overlay of a saddle.
2. Establish on the shock-absorber a boot, the limiter of a course of compression, a cup, metal and rubber plugs, a spring saddle with a slip.
3. Put on a shock-absorber rod the top plug A and a washer.
4. Screw new самоконтрящуюся a nut and temporarily it tighten.
5. Remove the tool compressing a spring, then tighten finally самоконтрящуюся a nut with demanded effort (25 H • м).
6. Establish a protective cover.
7. Establish shock-absorber assembly with a screw spring on the regular place on the car (see. Section Removal and installation of back racks).