The device, service, repair of Mitsubishi Galant (1990 — 2001) - Removal and installation of racks and screw springs of a forward suspension bracket//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Removal and installation of racks and screw springs of a forward suspension bracket

Details of installation of a rack of a forward suspension bracket on the Mirage models

1 — the Clamp of fastening of a brake hose
2 — the Wheel sensor (models with ABS)
3 — the Bolt of fastening of the bottom support (2 pieces)

4 — Samokontryashchayasya a nut
5 — Rack-mount assembly
N — Replace


The Diamante and Galant models on 1993 and since 1999 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
3. Remove from a rack a basic arm of the brake line, - do not hook a fixing collar any tools!
4. On the models equipped with ABS, release a clamp of fastening of the wheel sensor on rack-mount assembly.
5. Prop up a jack the bottom lever of a suspension bracket and give bolts of fastening of rack-mount assembly to a rotary fist. Tie up a rotary fist to suspension bracket elements so that not to allow a tension of a brake hose.
6. On models with an active suspension bracket (Active-ECS) release a nut of fastening of an air-line to the top part of a rack. Disconnect the line and remove a sealing ring, then turn out fixing and remove from a rack the actuation mechanism of Active-ECS system, - do not forget to disconnect electroconducting.
7. Mark the provision of the top support of a rack concerning a body, then release fixing nuts and remove rack-mount assembly from the car.


Installation

 PERFORMANCE ORDER

1. Establish rack-mount assembly on the regular place (track correctness of combination of the landing labels put in the course of dismantle), screw the top fixing nuts and tighten them with demanded effort (45 H • м).
2. Level a rack and connect it to assembly of a rotary fist, having tightened fixing bolts with demanded effort (90 ÷ 105 H • м).
3. On models with an active suspension bracket restore initial connection of an air-line (do not forget to replace a sealing ring) and establish into place the Active-ECS actuation mechanism, - do not forget to connect electroconducting.
4. Establish into place a basic arm with a brake hose. On models with ABS establish the wheel sensor.
5. Establish a wheel and lower the car on the earth.
6. In summary execute adjustment of corners of installation of forward wheels.


Mirage models

Removal

 PERFORMANCE ORDER

1. Details of installation of rack-mount assembly on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
4. On the models equipped with ABS, release a clamp of fastening of the wheel sensor on rack-mount assembly.
5. Prop up a jack the bottom lever of a suspension bracket and give bolts of fastening of rack-mount assembly to a rotary fist.
6. Mark the provision of the top support of a rack concerning a body, then turn out fixing bolts and remove rack-mount assembly from the car.


Installation

 PERFORMANCE ORDER

1. Establish rack-mount assembly on the regular place (track correctness of combination of the landing labels put in the course of dismantle), screw the top fixing nuts and tighten them with demanded effort (40 H • м).
2. Level a rack and connect it to assembly of a rotary fist, having tightened fixing bolts with demanded effort (110 ÷ 130 H • м).
3. Establish into place a basic arm with a brake hose. On models with ABS establish the wheel sensor.
4. Establish a wheel and lower the car on the earth.
5. In summary execute adjustment of corners of installation of forward wheels.


Galant 1994 ÷ 1998 models of вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
3. Disconnect a rack of the stabilizer of cross-section stability from a dempferny fork.
4. Turn out bottom through and top coupling bolts and remove assembly of a dempferny fork.

5. Give nuts of fastening of the top support and remove shock-absorber assembly with a screw spring from the car.


Installation

 PERFORMANCE ORDER

1. Establish the top support of the shock-absorber, - track correctness of an arrangement of three fixing bolts.
2. Establish the rubber plug of the top support, impose a washer, screw a lock-nut and tighten it with demanded effort (24 H • м).
3. Establish the shock-absorber and tighten the top nuts of its fastening with demanded effort (44 H • м).
4. Level a dempferny fork, establish the bottom through bolt of its fastening and tighten its nut with effort of 88 H • m. The top coupling bolt tighten with effort of 103 H • m.
5. Connect to a dempferny fork a rack of the stabilizer of cross-section stability and tighten a nut of its fastening with demanded effort (39 H • м).
6. Establish a wheel and lower the car on the earth.
7. In summary execute adjustment of corners of installation of forward wheels.