Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Removal and installation of wheel hairpins

Naves of the wheels equipped with disk brake mechanisms

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
2. Remove a support and blocks of the brake mechanism (see. Head Brake system). Tie up a support a wire to suspension bracket elements, - track, that the brake hose did not appear tense.
3. Remove stupichny assembly (see. Section Removal and installation of stupichny assemblies).

4. Transfer assembly on a workbench and establish on a suitable emphasis. By means of a press squeeze out of a disk wheel hairpins.

If possibility of use of a press is absent, hairpins can be beaten accurately out by means of a stupid brass drift, - track uniformity of an emphasis of a disk.


Installation

 PERFORMANCE ORDER

1. A rigid brush clean openings under installation of hairpins in stupichny assembly.
2. By means of a hammer fill a hairpin in a reception opening, - do not use any greasings and hermetics.

3. Final landing of hairpins is carried out by means of a press.

In the absence of possibility to use a press, pass a hairpin in a reception nest, then put on it about four flat washers and screw a wheel nut. Holding stupichny assembly start to tighten a nut, - the hairpin should come into a nest. Make sure of completeness of landing of a hairpin, then remove a nut and washers.

4. Establish stupichny assembly and adjust wheel bearings (see. Section Adjustment of wheel bearings).
5. Establish blocks and a support of the brake mechanism.
6. Establish a wheel and lower the car on the earth. Tighten wheel nuts with demanded effort.


Naves of the wheels equipped with drum-type brake mechanisms

Removal

 PERFORMANCE ORDER

1. Details of installation of wheel hairpins are shown on an illustration.

2. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
3. Remove a brake drum (see. Head Brake system).
4. In case of need remove brake boots (see. Head Brake system).

5. By means of a big clamp and a suitable face head squeeze out a hairpin of an axis flange.


Installation

 PERFORMANCE ORDER

1. Grease the surface of a hairpin equipped with a notch with liquid soap and pass it in a reception opening

2. Put on a hairpin about four flat washers and screw a wheel nut. Holding a flange from a provorachivaniye, start to tighten a nut, - the hairpin should come into a nest. Make sure of completeness of landing of a hairpin, then remove a nut and washers.

4. If removed, establish into place brake boots (see. Head Brake system).
5. Establish a brake drum (see. Head Brake system).
6. Establish a wheel and lower the car on the earth.
7. Tighten wheel nuts with demanded effort.