The device, service, repair of Mitsubishi Galant (1990 — 2001) - Removal and installation of the top operating levers of a back suspension bracket//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Removal and installation of the top managing directors of levers of a back suspension bracket

The Galant models for 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
3. Prop up a jack the bottom lever of a back suspension bracket.
4. Turn out a coupling bolt of a collar of fastening of the brake line.
5. Give a fixing nut and by means of the special tool of the MB9f35 type liberate the top spherical support from the longitudinal lever of a suspension bracket/fist of stupichny assembly, - if the support is subject to further use, act extremely carefully.
6. Mark position of the clown of the top adjusting bolt and turn out the last from the operating lever.
7. Remove the top lever from the car.


Installation

 PERFORMANCE ORDER

1. Establish the lever on the regular place, screw an adjusting bolt and слега tighten it, having achieved combination of the landing labels put in the course of dismantle.
2. Press the top spherical support in shpindelny assembly and tighten with demanded effort (72 H • м) a new fixing nut of a spherical finger.
3. Establish a wheel and lower the car on the earth.
4. Finally tighten with demanded effort (160 H • м) an adjusting bolt of the top lever.
5. Connect a negative wire to the battery.
6. Check corners of installation of back wheels, in case of need make the corresponding adjustment.


Galant 1994 ÷ 1998 models of вып.

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove assembly of the corresponding back wheel.

2. Turn out a through bolt of fastening of the top lever to a fist of stupichny assembly.

3. Turn out bolts of fastening of the top lever to a car body.

4. Remove assembly of the top lever.
5. In case of need give fixing nuts and take through bolts of fastening of basic arms of the top lever.


Installation

 PERFORMANCE ORDER

1. Establish on assembly of the top lever basic arms. Tighten nuts of fixing bolts with demanded effort (57 H • м).
2. Establish assembly of the top lever on the car and tighten four fixing bolts with effort of 39 H • m.
3. Establish a through bolt of fastening of the top lever to a fist of stupichny assembly, freely tighten a fixing nut.
4. Establish a wheel and lower the car on the earth.
5. Finally tighten with demanded effort (98 H • м) a nut of a through bolt.
6. Check corners of installation of back wheels, in case of need make the corresponding adjustment.


Diamante models

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Disconnect a bar of the stabilizer of cross-section stability and remove rack-mount assembly of a suspension bracket.
3. Prop up the longitudinal lever a jack and give самоконтрящуюся a nut of fastening of the managing director of the lever to it.
4. By means of a stripper liberate from the longitudinal lever the top spherical support.
5. Disconnect the operating lever from a stretcher and remove it from the car.


Installation

 PERFORMANCE ORDER

1. Establish the operating lever on a stretcher, slightly tighten a fixing bolt.
2. Connect the operating lever to the longitudinal lever and tighten самоконтрящуюся a nut with demanded effort (75 ÷ 89 H • м).
3. Establish rack-mount assembly and connect a bar of the stabilizer of cross-section stability.
4. Establish a wheel and lower the car on the earth.
5. Finally tighten a bolt of fastening of the lever to a stretcher with demanded effort (75 ÷ 89 H • м).
6. Check corners of installation of back wheels, in case of need make the corresponding adjustment.