Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
- Engine
   - Removal/installation of the power unit, dismantle of components
      General information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblies of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and turbokompressor installation
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal and installation of the oil pump
      Removal and installation of a damper of krutilny fluctuations of a cranked shaft
      Removal and installation of a cover of a drive of GRM and gas-distributing belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and flywheel installation / driving disk
   + Regenerative repair of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of a radiator of system of cooling (all models)

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Empty cooling system.

In order to avoid receiving burns, start performance of the listed works only after final cooling of system! Do not allow antifreeze hit on open sites of a body and the painted surfaces of the car. Casually got splashes immediately wash away a plentiful quantity of water. Remember that antifreeze is extremely toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze being stored in leaky closed container and immediately collect cooling liquid spilled on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways utilization of the fulfilled cooling liquid consult at any station of car-care center. In many regions of the world special points on different reception of working off are equipped. At all do not merge old cooling liquid in the sewerage and on the earth!

3. Disconnect a perelivny tube (on some models it is necessary to remove also a broad tank).

4. Disconnect the top and bottom radiatorny hoses.

5. Disconnect electroconducting from fans of systems of cooling and air conditioning.

6. On the Mirage and Diamante models remove ventilyatorny assembly.

7. Disconnect electroconducting from the thermosensitive sensor.

8. On models from AT disconnect lines of cooling of ATF, - at once закупорьте the open ends of tubes and unions.

9. Remove the top support and take a radiator/radiator complete with ventilyatorny assembly.


Installation

 PERFORMANCE ORDER

1. Establish into place a radiator/radiator complete with ventilyatorny assembly.
2. Connect lines of cooling of ATF.
3. Connect electroconducting to the thermosensitive sensor.
4. If removed, establish into place ventilyatorny assembly.
5. Connect radiatorny hoses.
6. If removed, establish into place a basic arm of an air purifier.
7. Establish a broad tank of system of cooling and connect perelivny a hose.
8. Fill cooling system (see. Head of Control and routine maintenance).
9. Connect a negative wire to the battery. Start the engine and warm up it to normal working temperature, then correct level of cooling liquid in a radiator, on models from AT check ATF level.
10. Wait complete cooling of the engine, then once again check level of cooling liquid. In case of need make the corresponding adjustment.