Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
- Engine
   - Removal/installation of the power unit, dismantle of components
      General information
      Removal and engine installation
      Removal and installation of a cover of a head of cylinders
      Removal and installation of assemblies of a drive of valves
      Removal and thermostat installation
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal and turbokompressor installation
      Removal and installation of a radiator of system of cooling (all models)
      Removal and installation of the fan of system of cooling of the engine
      Removal and installation of the water pump
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal and installation of the oil pump
      Removal and installation of a damper of krutilny fluctuations of a cranked shaft
      Removal and installation of a cover of a drive of GRM and gas-distributing belt
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of camshafts and pushers of a drive of valves, check of a condition of components
      Removal and installation of a balancing shaft
      Replacement of a back epiploon of a cranked shaft
      Removal and flywheel installation / driving disk
   + Regenerative repair of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of a damper of krutilny fluctuations of a cranked shaft

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Throw off from a pulley of a cranked shaft belts of a drive of auxiliary units (see. Head of Control and routine maintenance).
3. To Poddomkratta the car also establish it on props.
4. Remove the right forward wheel (from the passenger party of the car).

5. For the purpose of ensuring access to a damper of krutilny fluctuations remove a loker of protection of a wheel arch.

6. On models of 1.5 l, 1.6 l, 2.0 l and 2.4 l turn out bolts of fastening of a pulley to a cogwheel of a cranked shaft. On models of 1.5 l, 1.8 l, 3.0 l and 3.5 l turn out the central bolt of fastening of a pulley of a cranked shaft.

7. By means of a stripper dismantle a damper of krutilny fluctuations from a shaft pin.


Installation

 PERFORMANCE ORDER

1. Having tracked shponka hit in a reciprocal groove, plant a damper of krutilny fluctuations on a pin of a cranked shaft,
2. On models of 1.5 l, 1.8 l, 3.0 l and 3.5 l screw the central bolt of fastening of a pulley and tighten it with demanded effort (70 ÷ 100 H • m - for models of 1.5 l, 185 H • m - for models of 1.8 l and 3.5 l and 150 ÷ 160 H • m - for models of 3.0 l).
3. On models of 1.5 l, 1.6 l, 2.0 l and 3.5 l screw bolts of fastening of a pulley to a shaft cogwheel. Tighten fixture with demanded effort (14 H • m - for models of 1.5 l, 20 ÷ 30 H • m - for models 1.6 and 2.0 of l and 25 H • m - for models of 2.4 l).
4. Establish into place a loker of protection of a wheel arch.
5. Establish a wheel, lower the car on the earth and tighten wheel nuts.
6. Establish belts of a drive of auxiliary units (see. Head of Control and routine maintenance).
7. Connect a negative wire to the battery.