Mitsubishi Galant

1. Details of installation of sensors of turns of forward wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect from the wheel sensor electroconducting.
6. Remove clamps of fastening of a plait of electroconducting of the sensor.
7. Remove the sensor from a basic arm.

1. Establish the sensor on a basic arm and tighten a fixing bolt.
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the sensor.
4. Connect a negative wire to the battery.

1. Details of installation of sensors of turns of back wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
4. Disconnect from the wheel sensor electroconducting.
5. Remove clamps of fastening of a plait of electroconducting of the sensor.
6. Turn out a fixing bolt and remove the wheel sensor.

1. Establish the sensor on the regular place and freely tighten a fixing bolt.
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the sensor.

4. By means of not magnetic щупа lezviyny type adjust a gap between the sensor and its rotor, - demanded value makes 0.3 — 0.9 mm.

5. Finally tighten fixture and once again check correctness of installation of a gap. In case of need repeat adjustment.
6. Connect a negative wire to the battery.

1. Details of installation of wheel sensors on the Galant models are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding forward wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect from the wheel sensor electroconducting.
6. Turn out coupling bolts and remove collars of fastening of a plait of electroconducting of the sensor.
7. Turn out a fixing bolt and remove the wheel sensor.

1. Establish the sensor on the regular place and tighten a fixing bolt.

The gap between the sensor and its rotor is not subject to adjustment, however should be checked. Demanded value makes 28.2 ÷ 28.4 mm. At an exit of result of change out of limits of an admissible range replace the sensor or a rotor.

2. Fix a plait of electroconducting of the sensor bandage collars, - strongly tighten coupling bolts.
3. Connect electroconducting to the sensor.
4. Establish a loker of protection of a wheel arch.
5. Establish into place a wheel and lower the car on the earth.
6. Connect a negative wire to the battery.

1. Details of installation of wheel sensors are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding forward wheel.
4. Disconnect from the wheel sensor electroconducting.
5. Turn out coupling bolts and remove collars of fastening of a plait of electroconducting of the sensor.
6. Turn out a fixing bolt and remove the wheel sensor.

1. Establish the sensor on the regular place and tighten a fixing bolt.

The gap between the sensor and its rotor is not subject to adjustment, however should be checked. Demanded value makes 28.2 ÷ 28.4 mm. At an exit of result of change out of limits of an admissible range replace the sensor or a rotor.

2. Fix a plait of electroconducting of the sensor bandage collars, - strongly tighten coupling bolts.
3. Connect electroconducting to the sensor.
4. Establish into place a wheel and lower the car on the earth.
5. Connect a negative wire to the battery.

1. Details of installation of sensors of turns of forward wheels on the Diamante models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
4. Remove a loker of protection of a wheel arch.
5. Disconnect from the wheel sensor electroconducting.
6. Remove clamps of fastening of a plait of electroconducting of the sensor.
7. Remove the wheel sensor.

1. Establish the sensor on the regular place and tighten it with demanded effort (12 H • м).
2. Establish clamps of fastening of a plait of electroconducting.
3. Connect electroconducting to the sensor.
4. Connect a negative wire to the battery.

1. Details of installation of sensors of turns of back wheels on the Mirage models are shown on an illustration.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! In order to avoid operation of safety cushions start sensor dismantle not less than 90 seconds later after battery shutdown.

3. To Poddomkratta the car also establish it on props. Remove the corresponding wheel.
4. Disconnect from the wheel sensor electroconducting.
5. Remove clamps of fastening of a plait of electroconducting of the sensor.
6. On all-wheel drive (AWD) models remove a hummock bandage.
7. Turn out a fixing bolt and remove the wheel sensor together with a sealing ring.

1. Establish the sensor on the regular place (do not forget to replace a sealing ring) and tighten it with demanded effort (12 H • м).
2. Establish clamps of fastening of a plait of electroconducting.
3. Establish a hummock bandage.
4. Connect electroconducting to the sensor.
5. Connect a negative wire to the battery.