The device, service, repair of Mitsubishi Galant (1990 — 2001) - Adjustment of the parking brake//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
- Brake system
   Specifications
   Replacement of the sensor switch of stoplights
   Removal and GTTs installation
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning/tightness, removal and installation of the vacuum amplifier of brakes
   Removal and valve regulator installation
   Removal and installation of brake lines
   Pumping of brake system
   Disk brake mechanisms - the general information
   Assessment of a condition of brake shoes
   Replacement of blocks of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Regenerative repair of a support of the disk brake mechanism
   Removal, check of a condition and installation of a brake disk
   Drum-type brake mechanisms - the general information
   Removal, installation and check of a condition of a brake drum
   Check of a condition of brake boots
   Removal and installation of brake boots
   Adjustment of drum-type brake mechanisms
   Removal, regenerative repair and installation of wheel cylinders
   Removal and cable installation (ов) drive of the parking brake
   Adjustment of the parking brake
   Removal and installation of frictional boots of the parking brake (model with disk brake mechanisms of back wheels)
   System of anti-blocking of brakes (ABS) - the general information, problem diagnostics and codes of malfunctions
   Removal and installation of the hydraulic modulator
   Removal and ABS control unit installation
   Removal and installation of wheel sensors
   Removal and installation of sensors of accelerations (G-sensors)
   Replacement of rotors of wheel sensors
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Adjustment of the parking brake

Mirage models

On the models equipped with drum-type brake mechanisms of back wheels, previously it is necessary to adjust brake boots of the main brake mechanism.


 PERFORMANCE ORDER

1. Check freedom of a course of a driving cable of the parking brake.
2. Counting number of clicks of a ratchet, cock the lever of the parking brake with effort of 200 N. Recommended value makes 5 ÷ 7 clicks.
3. In case of need make adjustment.

4. Access to an adjusting nut is possible from within floor section of the central console.

5. Weaken a lock nut of a rod of hummock assembly.
6. Rotation of an adjusting nut achieve demanded result (by number of clicks of a ratchet). Track, that between an adjusting nut and the lever it was not formed люфт, then tighten a lock nut.

Be not overzealous, - excessively hard tension of a cable can lead to failure of automatic regulators of brake mechanisms, and also "prikhvatyvaniye" of brakes!

7. Having finished adjustment of a course of the lever, поддомкратьте a car back also check freedom of rotation of back wheels at the released parking brake.
8. Check reliability of keeping of the car the parking brake on a bias.


The Galant models for 1993 вып.

 PERFORMANCE ORDER

1. As well as in the previous case, when raising lever with effort of 200 N the ratchet should make from 5 to 7 clicks. Knots of a drive of the parking brake subject to adjustment are shown on an illustration.

2. Before starting adjustment of a hummock drive, it is necessary to adjust boots of the parking brake for what поддомкратьте the car and establish it on props. Take from a brake disk a cap, remove a support and tie up it a wire to suspension bracket elements, without disconnecting the hydraulic line. Rotating a self-regulator castor the suitable tool, block rotation of a brake disk. Turn off a castor on five рисок in the opposite direction and make sure that the disk is turned with easy resistance. Establish into place a support and check serviceability of functioning of the brake mechanism.
3. Having finished adjustment of frictional boots of the parking brake, start adjustment of a hummock drive.
4. Rotation of an adjusting nut achieve demanded number of clicks of a ratchet when raising the lever of the parking brake with a certain effort.
5. To Poddomkratta a car back also establish it on props and check freedom of rotation of back wheels at the released parking brake. In case of need release a little adjusting nut.


The Galant models since 1994 вып.

 PERFORMANCE ORDER

1. Requirements for number of clicks of a ratchet when raising lever with effort of 200 N remain former (5 ÷ 7 clicks). In case of need make the corresponding adjustment.
2. Remove an internal mat of floor section of the central console.
3. Having released an adjusting nut on the end of a rod of hummock assembly, weaken a drive tension.
4. At the engine working at single turns five-six times firmly squeeze out a pedal of a foot brake, - the course of a pedal should be stabilized that confirms serviceability of functioning of the mechanism of an automatic regulator and correctness of installation of a gap between boots and a working surface of a brake drum.
5. Further, in a standard manner (see the previous subsection) execute adjustment of a hummock drive. To Poddomkratta a car back also check freedom of rotation of back wheels at the released parking brake.


Diamante models

 PERFORMANCE ORDER

1. On the Diamante models raising of the lever of the parking brake with effort of 200 N should be accompanied by three-five clicks of a ratchet.
2. Check correctness of adjustment of boots of the parking brake, in case of need make the corresponding adjustment.
3. Remove floor section of the central console. Release the lever of the parking brake and give a regulator lock-nut in the basis of lever assembly.
4. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel and take a cap from a brake disk.
5. Remove a brake support and, without disconnecting the hydraulic line, tie up it a wire to a suspension bracket element.
6. Rotating a self-regulator castor the suitable tool, block rotation of a brake disk. Turn off a castor on five рисок in the opposite direction and make sure that the disk is turned with easy resistance.
7. Establish into place a support and check serviceability of functioning of the brake mechanism.
8. Having finished adjustment of frictional boots of the parking brake, start adjustment of a hummock drive.
9. Rotation of an adjusting nut achieve demanded number of clicks of a ratchet when raising the lever of the parking brake with a certain effort.
10. To Poddomkratta a car back also establish it on props and check freedom of rotation of back wheels at the released parking brake. In case of need release a little adjusting nut.