Mitsubishi Galant

1990 — 2001 of release

Repair and car operation

Removal, installation and check of a condition of a brake drum

Design of the drum-type brake mechanism used on the Mirage models for 1992 вып.


1 — the Cover of a stupichny nut 2 — Stupichnaya a nut 3 — the Internal holder of the external bearing 4 — the Brake drum 5 — the Spring of fastening of a boot to the regulator lever 6 — the regulator Lever 7 — Assembly of an automatic regulator 8 — the Bottom coupling spring 9 — Plates of directing springs 10 — Directing springs of boots 11 — the Top coupling spring	12 — the Brake boot 13 — boot Assembly with anchor knot 14 — the Holder 15 — the Wavy washer 16 — the Executive lever of a drive of the parking brake 17 — the Brake boot 18 — the Anchor finger 19 — the Brake tube 20 — the Lock ring 21 — the Brake board

Design of the drum-type brake mechanism used on the Galant and Mirage models since 1993 вып.


1 — the Brake drum 2 — the Spring of fastening of a boot to the regulator lever 3 — the regulator Lever 4 — Assembly of an automatic regulator 5 — the Bottom coupling spring 6 — Plates of directing springs 7 — Directing springs of boots 8 — Plates of directing springs 9 — the Top coupling spring 10 — the Brake boot with a frictional slip	11 — Assembly of a brake boot with the adjusting lever 12 — the Holder 13 — the Wavy washer 14 — the Executive lever of a drive of the parking brake 15 — the Brake boot with a frictional slip 16 — the Anchor finger 17 — the Brake tube 18 — the Lock ring 19 — Stupichnaya assembly 20 — the Brake board

Remember that developed in the course of operation of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system by gasoline or solvents on an oil basis, - apply only firm cleaners or methyl alcohol!

The Mirage models for 1992 вып.

Removal

PERFORMANCE ORDER

1. A design of the drum-type brake mechanism used on the Mirage models for 1992 вып. it is presented on an illustration.
2. To Poddomkratta the car also establish it on props.
3. Remove the corresponding back wheel.
4. Remove a dustproof cover of a stupichny nut.
5. Give самоконтрящуюся a stupichny nut.
6. Remove the external wheel bearing.
7. Remove from a spindle a brake drum assembled with the internal wheel bearing.
8. Remove an epiploon.

Installation

PERFORMANCE ORDER

1. For validity check to further use самоконтрящейся nuts screw it on a spindle so that the end of the last came to light approximately on 3 mm. Measure a torque of resistance to nut rotation counter-clockwise. The result of measurement makes less than 5.5 H • m, the nut is subject to replacement.
2. Grease and establish the internal bearing.
3. Establish a new epiploon.
4. Put on a spindle a brake drum.
5. Grease and establish the external wheel bearing.
6. Tighten самоконтрящуюся a stupichny nut with demanded effort (150 ÷ 200 H • м).
7. Establish a protective cover.

Condition check

PERFORMANCE ORDER

1. Measure internal diameter of the brake drum removed from the car, - for the purpose of identification of signs of ovality measurement should be made in several points.

2. If the result of measurement exceeds maximum permissible value (231 mm), replace a drum complete with boots (see. Section Removal and installation of brake boots).

The Galant and Mirage models since 1993 вып.

Removal

PERFORMANCE ORDER

1. A design of the drum-type brake mechanism used on the Galant and Mirage models since 1993 вып. it is presented on an illustration.
2. To Poddomkratta the car also establish it on props.
3. Remove the corresponding back wheel.
4. Weaken an adjusting nut of a drive of the parking brake.

5. Having pulled on itself, remove a brake drum from stupichny assembly, - in case of need обстучите assembly by a hammer with soft brisk for the purpose of its release. If the disk at boiled and does not give in to removal, screw in two specially provided carving openings in its obverse surface pair of bolts suitable on the size and, gradually tightening them, release a drum.

Installation

PERFORMANCE ORDER

1. Establish a drum on a nave.
2. Establish a wheel adjust a drive of the parking brake.
3. Lower the car on the earth.