Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
- Settings and routine maintenance
   Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Replacement of impellent oil and oil filter
   Check, service and charging of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement of ATF of automatic transmission and differential of the main transfer, check of a condition and AT filter service
   Check of a condition of brake lines
   Check condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of gaps of valves - only Mirage
   Replacement of a filtering element of an air purifier
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation of a case (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement of driving belts
   Check of a condition of components of system of production of the fulfilled gases
   RKPP transmission oil replacement
   Replacement of greasing of a transfer case - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of the parking brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of a power supply system
   Check of a condition and belt replacement GRM drive (it)
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Check condition/service of drum-type brake mechanisms

 PERFORMANCE ORDER

1. Remove brake drums (see. Head Brake system).

2. Make careful cleaning of brake mechanisms with application of special cleaning structure.

At all do not blow off a brake dust from a surface of components the compressed air and do not inhale it - the dust can contain asbestos harmful to your health!

Estimate residual thickness of frictional overlays of brake boots (forward and back), check components on existence of traces of pollution by brake liquid and oil. If the frictional slip acts over heads of rivets / a metal substrate of assembly less than on 1.6 mm, boots are subject to replacement in a set (see. Head Brake system). It is necessary to replace boots also in case of identification of cracks, zapolirovanny to shine of sites of slips, or traces of hit of brake liquid.

3. Make sure of correctness of connection and serviceability of a condition of all springs of assembly of the brake mechanism (see. Head Brake system). The neglect replacement of the deformed or weakened springs is fraught with premature wear of boots as a result "prikhvatyvaniye" of brakes.
4. Check assembly components on existence of traces of leakages of brake liquid. Having carefully hooked a finger or a small screw-driver, remove rubber boots from the wheel cylinder in the top part of boots. Identification of any signs of leaks in these parts demands carrying out immediate regenerative repair of assembly of the cylinder (see. Head Brake system). Also check on existence of traces of leaks all brake hoses and their shtutserny connections.
5. Carefully wipe internal surfaces of a drum the pure rags impregnated with methyl alcohol. Try not to inhale a brake dust containing asbestos. Examine a working surface of a drum on existence of cracks, задиров, traces of an overheat and other damages. If defects cannot be removed with a way of processing of a surface a fine-grained emery paper, it is necessary to give a drum for a pro-point to a car-care center workshop (see. Head Brake system).
6. Repeat procedure for components of the opposite brake mechanism. Establish into place drums, fix wheels and lower the car on the earth. Tighten wheel nuts with demanded effort.