Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
- Settings and routine maintenance
   Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Replacement of impellent oil and oil filter
   Check, service and charging of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement of ATF of automatic transmission and differential of the main transfer, check of a condition and AT filter service
   Check of a condition of brake lines
   Check condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of gaps of valves - only Mirage
   Replacement of a filtering element of an air purifier
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation of a case (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement of driving belts
   Check of a condition of components of system of production of the fulfilled gases
   RKPP transmission oil replacement
   Replacement of greasing of a transfer case - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of the parking brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of a power supply system
   Check of a condition and belt replacement GRM drive (it)
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Service of system of cooling

 PERFORMANCE ORDER

Do not allow antifreeze hit on open sites of a body and the painted surfaces of the car. Casual splashes immediately wash away a plentiful quantity of water. Remember that antifreeze is extremely toxic liquid and its hit in an organism even in small amounts is fraught with the most serious consequences (up to a lethal outcome). Never leave antifreeze being stored in leaky closed container and immediately collect cooling liquid spilled on a floor. Remember that the sweetish smell of antifreeze can draw to itself attention of children and animals. About ways utilization of the fulfilled cooling liquid consult with local authorities. In many regions of the world special points on different reception of working off are equipped. At all do not merge old cooling liquid in the sewerage and on the earth!


Recently nontoxical grades of antifreeze were developed, however they also demand care in the address.

1. Regularly, according to the schedule of routine maintenance of the car (see. Undressed the Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars), the system of cooling should be emptied, washed out and filled with a fresh mix of antifreeze with water. Such service allows to prevent corrosion development in an okhladitelny path and considerably increases efficiency of functioning of system.
2. During service also the condition of all hoses of system and a cover of a jellied mouth of a radiator (without fail should be checked see. Section Check of a condition of components of system of cooling). Defective components are subject to replacement. Do not forget about precautionary measures which should be observed at service of system of cooling (see the prevention at the beginning of the Section). Remember that the fulfilled cooling liquid is subject to utilization and should not merge in the sewerage at all.


Oporozhneniye

 PERFORMANCE ORDER

1. Cock the parking brake and prop up wheels protivootkatny boots, in case of need поддомкратьте the car and establish it on props. It is necessary to start direct performance of procedures of service after complete cooling of the engine, i.e., some hours later after trip end.
2. Uncover a broad tank/radiator.

In order to avoid receiving burns, do not uncover at all a radiator / a broad tank, without having waited final cooling of the engine!

3. At the corresponding complete set of the car remove elements of protection of a case.
4. Get drain capacity under the drain gate of a radiator, open the gate and lower cooling liquid in the prepared capacity.

For the purpose of decrease in risk of casual damage of the gate made of plastic, previously moisten it with getting oil.


5. Having waited a radiator oporozhneniye, close the gate and take from under the car drain capacity. In case of need establish into place protection of a case.
6. Lower the car on the earth.


Washing

 PERFORMANCE ORDER

1. Having completely emptied cooling system (see above), fill in in it special flushing liquid (as a last resort will approach soft water is usual).
2. Start the engine and wait, while the top radiatorny hose does not become hot to the touch.
3. Having muffled the engine, wait its complete cooling and again empty system.
4. Repeat the described procedure until liquid merged from a radiator completely will not be released from the maintenance of particles of a scum and will not gain absolute transparency.
5. Separately wash out a broad tank.
6. Having tightened the drain gate and, in case of need, having restored initial connection of all hoses, fill in in system fresh cooling liquid of demanded structure, then remove from an okhladitelny path air jams (see further).


Filling

 PERFORMANCE ORDER

1. Slowly fill in in a radiator the fresh, made in proportions 50 x 50th mix of antifreeze with water. Continue filling until level of liquid will not rise to the bottom cut of a jellied mouth. Add cooling liquid in a broad tank, having finished its level to the bottom mark (FULL COLD) in a tank wall. Wait five minutes and once again check level of cooling liquid in a radiator, in case of need make adjustment.
2. Without establishing a cover on a radiator, start the engine and warm up it before opening of the valve of the thermostat (liquid should start to circulate through a radiator, thus there will be a warming up of the top hose of the last).
3. Muffle the engine and let's to it cool down. Add in a radiator a little more liquid, having finished its level to the bottom cut of a jellied mouth.
4. By a szhimaniye of the top hose of a radiator let out from it air, in case of need add a little more cooling liquid. Establish into place a radiator cover.
5. Transfer the handle of management of system of heating of salon to the maximum heating, turn on for the maximum speed the heater fan.
6. Start the engine, warm up it to normal working temperature and check system on existence of signs of leaks.
7. Overheating of the unit testifies to existence in an okhladitelny path of air jams. Muffle the engine and let's to it cool down, - air should leave a path automatically. Repeating procedure, achieve a demanded temperature mode of the working engine.
8. Once again check level of cooling liquid in a broad tank, in case of need make the corresponding adjustment.