Mitsubishi Galant

1990 — 2001 of release

Repair and car operation

Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
- Settings and routine maintenance
   Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Replacement of impellent oil and oil filter
   Check, service and charging of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement of ATF of automatic transmission and differential of the main transfer, check of a condition and AT filter service
   Check of a condition of brake lines
   Check condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of gaps of valves - only Mirage
   Replacement of a filtering element of an air purifier
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation of a case (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement of driving belts
   Check of a condition of components of system of production of the fulfilled gases
   RKPP transmission oil replacement
   Replacement of greasing of a transfer case - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of the parking brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of a power supply system
   Check of a condition and belt replacement GRM drive (it)
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Greasing of components of the chassis

List of the materials necessary for greasing of components of the chassis

1 — Liquid impellent oil - is used for greasing of door loops
2 — the Graphite aerosol - is used for greasing of zamkovy cylinders

3 — Greasing - in the market the wide range of greasings of various type and the viscosity intended for a zakachivaniye by means of the lubricant gun is presented
4 — the Lubricant gun - is intended for stuffing of components by greasing, is used complete with different nozzles and transitional hoses


1. Prepare a necessary stock of greasing of a demanded grade (see. Specifications) and the lubricant gun for stuffing of hollow components.

On some knots instead of lubricant unions can appear caps are established, - take care also of existence near at hand a set of unions, - carving shtutserny nozzles of the various form providing adequate access practically to any component are issued.

2. Having glanced under the car, find lubricant unions of components of a steering drive, a suspension bracket and the transmission line. Usually unions enter into a regular complete set of such knots, as tips of steering drafts and kardanny hinges. If instead of unions caps are established, instead of them it is necessary to screw the prepared shtutserny nozzles.
3. To Poddomkratta the car also establish it on the props got under a frame, or tire out its lift.

 If assume to make at this stage rotation of wheels, do not forget to weaken fixing nuts before they will be torn off from the earth.

4. For pro-cleaning of a nozzle of the gun from dirt squeeze out a little greasing. Wipe a nozzle pure rags.
5. Prepare a stock of rags and start stuffing of components by greasing.
6. Wipe the lubricant union and a surface of a component surrounding it pure rags, connect to the union a nozzle of the gun and start stuffing. Continue to pump greasing until it will not start to exude through joints of landing surfaces of a component.

If greasing starts to exude through a gun nozzle, it is necessary to clean and give particular attention it to clip density. In case of need replace the union.

7. Rags collect from a component surface excess of greasing and pass to stuffing of the following knot.

8. Stuffing of a sliding collar of the universal hinge of the driveshaft continue until greasing will not start to exude an assembly epiploon.

9. When stuffing kardanny hinges of usual type greasing should start to exude through joints of components of assembly.

10. Without getting out from under the car, wipe cables of a drive of the parking brake and with fingers grease their directing and executive levers.

11. At the corresponding complete set of the car put greasing on a lithium basis on contact surfaces of persistent arms and adjusting bolts of assemblies of rotary fists.

12. Open a cowl and fill a little greasing for the chassis in the mechanism of a latch of the lock. Ask the assistant to extend against the stop the lever of an otpuskaniye of the lock of a cowl under the dashboard and grease all being bared surfaces of a driving cable.
13. With liquid impellent oil grease loops of all doors and a cowl.
14. For greasing of zamkovy cylinders it is most convenient to use the graphite greasing delivered in aerosol ballonchik, - ask in shops of automobile accessories.
15. With silicone greasing grease sealing tapes of doors for the purpose of protection them from premature wear.