Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
- Settings and routine maintenance
   Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Replacement of impellent oil and oil filter
   Check, service and charging of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement of ATF of automatic transmission and differential of the main transfer, check of a condition and AT filter service
   Check of a condition of brake lines
   Check condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of gaps of valves - only Mirage
   Replacement of a filtering element of an air purifier
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation of a case (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement of driving belts
   Check of a condition of components of system of production of the fulfilled gases
   RKPP transmission oil replacement
   Replacement of greasing of a transfer case - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of the parking brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of a power supply system
   Check of a condition and belt replacement GRM drive (it)
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Check of a condition of components of system of production of the fulfilled gases

 PERFORMANCE ORDER

1. Having waited complete cooling of system of production of the fulfilled gases (not less than three hours later after an engine stop), attentively examine all its components, beginning from a flange of fastening of a reception pipe to a final collector, and finishing a cut of an exhaust pipe. For providing a free access under the car hang out it by means of the winch/hydrolift, or tire out on a platform or a viewing hole.

Remember that the catalytic converter (if that is provided) can remain warmed up much more long than other components of system of release, - be careful!


2. Check sections of system and a place of their joints on existence of signs of development of leakages of the fulfilled gases, traces of corrosion and mechanical damages, make sure of reliability of a tightening of fixture, check a condition and durability of fastening of arms and rubber подвесов system components.

3. At the same time examine the vehicle bottom on existence of holes, traces of development of corrosion, a divergence of welded seams and the other damages allowing fulfilled gases to get into salon of the car. Zagermetiziruyte all found openings silicone hermetic or a usual body shpatlevka.

4. The roar and many other extraneous noise during movement often appear a consequence of weakening of fixture of components of system of release, or shift of its sections. Attentively check a condition of arms and подвесов, pull pipes, the exhaust silencer and the catalytic converter, checking, whether they adjoin to bottom or suspension bracket elements. In case of need replace components of support of system.

5. On appearance of a cut of an exhaust pipe it is possible to estimate the general working condition of the engine with high degree of reliability. The consistence and color covering the end of a pipe of deposits allow to reveal violations of adjustments of the engine. If the pipe is covered with black sazhisty deposits, or on it the raid of whitish color, the engine, together with a power supply system was formed, needs control.