Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
- Coupling and transmission line
   Specifications
   Coupling - the general information and check of a condition of components
   Removal, check of a condition and installation of components of assembly of coupling
   Removal, check of a condition and installation of the vyzhimny bearing and fork of switching off of coupling
   Check of a condition and replacement of the directing bearing
   Adjustment of a pedal of coupling
   Adjustment of a cable of a drive of coupling, removal and installation of hummock assembly (the Mirage model with a hummock drive of coupling)
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Air removal from a hydraulic path of a drive of switching off of coupling
   Removal and installation of power shafts
   Hinges of power shafts - the general information and service
   Check of a condition of the transmission line
   Removal and driveshaft installation
   Replacement of the kardanny hinge
   Driveshaft balancing
   Removal and installation of assembly of the central bearing of the driveshaft
   Removal and installation of back semi-axes (the AWD Galant model for 1993 вып.)
   Removal and installation of a stupichny pin of a back axis, wheel bearing and epiploon
   Replacement of an epiploon of a leading gear wheel of back differential
   Removal and installation a case of back differential (the AWD Galant model for 1993 вып.)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal, check of a condition and installation of the vyzhimny bearing and fork of switching off of coupling

Remember that developed in the course of wear of frictional overlays of a conducted disk of coupling the dust can contain unhealthy asbestos. Do not blow off a dust the compressed air and try not to inhale it. Do not apply to rubbing of components of coupling solvents on an oil basis, - use only special brake cleaners or pure methyl alcohol. The used rags before utilization put in tightly closed container.


Removal

 PERFORMANCE ORDER

1. Remove assembly of the executive cylinder of coupling (see. Section Removal and installation of the executive cylinder of coupling).
2. Remove a transmission (see. Head Manual transmission).
3. Remove the holder of the lever of switching off of coupling from a spherical finger of a spherical support.

4. Try to remember how fingers of the lever of switching off fasten on the vyzhimny bearing a spring clamp. Remove the bearing from lever assembly, then - from a pin of primary shaft of a transmission. Remove the lever of switching off of coupling. estimate a condition of a rubber protective cover of the lever, in case of need replace a boot. Estimate a condition of the wire holder of the lever, in case of need make replacement. Check the lever of switching off of coupling on existence of cracks and signs of deformations.


Check

 PERFORMANCE ORDER

Holding the bearing for an external holder, press two fingers internal and повращайте it. The bearing should rotate freely and silently, otherwise it is necessary to replace it. Wipe the bearing pure rags and examine on existence of signs of wear, cracks and other mechanical damages. Usually replacement of the vyzhimny bearing is made each time at service of components of coupling. At all do not wash out the bearing in solvent in order to avoid violation of tightness of its assembly.


Installation

 PERFORMANCE ORDER

1. Grease contact surfaces of the lever of switching off of coupling with refractory greasing. In case of need plant on a place the new spring holder. Fill greasing in an internal flute of the vyzhimny bearing. Also grease the holder of the bearing on a pin of primary shaft.

2. Establish vyzhimny the bearing on assembly of the lever of switching off, - track reliability of fixing of components.
3. Grease with refractory greasing a surface of a spherical finger of a spherical support of the lever, pass the lever through a boot, plant the bearing on a shaft pin, then latch the lever on a support finger. Check freedom of moving of the bearing on a shaft pin.

4. Slightly grease with high-temperature greasing contacting to petals of a diafragmenny spring of a press disk a surface of the vyzhimny bearing.
5. Further installation is made as it should be the return to an order of dismantle of components. Track, bolts of fastening of transmission to the engine were tightened with demanded effort (see. Specifications to Head the Manual transmission).