Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
- Coupling and transmission line
   Specifications
   Coupling - the general information and check of a condition of components
   Removal, check of a condition and installation of components of assembly of coupling
   Removal, check of a condition and installation of the vyzhimny bearing and fork of switching off of coupling
   Check of a condition and replacement of the directing bearing
   Adjustment of a pedal of coupling
   Adjustment of a cable of a drive of coupling, removal and installation of hummock assembly (the Mirage model with a hummock drive of coupling)
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Air removal from a hydraulic path of a drive of switching off of coupling
   Removal and installation of power shafts
   Hinges of power shafts - the general information and service
   Check of a condition of the transmission line
   Removal and driveshaft installation
   Replacement of the kardanny hinge
   Driveshaft balancing
   Removal and installation of assembly of the central bearing of the driveshaft
   Removal and installation of back semi-axes (the AWD Galant model for 1993 вып.)
   Removal and installation of a stupichny pin of a back axis, wheel bearing and epiploon
   Replacement of an epiploon of a leading gear wheel of back differential
   Removal and installation a case of back differential (the AWD Galant model for 1993 вып.)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of a stupichny pin of a back axis, wheel bearing and epiploon

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. Remove the corresponding back wheel.
4. On the models equipped with ABS, remove the wheel sensor, - in order to avoid a sensor exit out of operation try not to allow its electric contact to metal elements of a suspension bracket.
5. Remove a support of the back brake mechanism and, without disconnecting the hydraulic line, tie up it a wire to suspension bracket elements, remove a brake disk.
6. Turn out bolts of fastening of a semi-axis to a connecting flange, give nuts and remove washers, - for the purpose of ensuring access to самоконтрящейся to a nut slightly take the semi-axis end aside.
7. By means of the special tool of the MB9b11-01 type block a semi-axis, then give самоконтрящуюся a nut.
8. By means of a stripper with a nozzle (MB9b11-01 and MB9b41-01) liberate a pin of a back axis from assembly of the longitudinal lever of a suspension bracket.
9. On the equipped ABS models remove from a pin a rotor of the wheel sensor (use the suitable plug and a press).
10. By means of a press remove from a pin the external bearing with a dustproof cover.
11. By means of a stripper liberate from assembly of the longitudinal lever an epiploon and the internal bearing.
12. Estimate a condition of a connecting flange and an axis pin. Check a dustproof cover on existence of signs of deformations and other mechanical damages. Attentively examine bearings on existence of traces of an overheat. Defective components replace.


Installation

 PERFORMANCE ORDER

1. Having used a suitable opravka, plant in assembly of the longitudinal lever the internal bearing. Afterwards establish an epiploon (a curve up and against the stop in a coat hanger of the internal lever).

As an opravka for landing of an epiploon it is possible to use a face head suitable on the size, or a piece of a pipe of the corresponding diameter. Zastukivayte an epiploon gradually and evenly, - use a hammer with soft the brisk.

2. Against the stop in a coat hanger plant dustproof caps (the internal - deepening outside).
3. Grease with universal greasing an internal surface of sealing sponges of an epiploon of the external bearing. Plant the bearing on an axis pin (epiploon sponges to a connecting flange).
4. Press into place a rotok of the wheel sensor (a flute towards a flange).
5. Temporarily establish a pin on assembly of the longitudinal lever. Establish a connecting flange and screw new самоконтрящуюся a nut.
6. Holding a pin from a provorachivaniye by means of the special MB9b11-01 adaptation, tighten самоконтрящуюся a nut with demanded effort (220 H • м).
7. Establish new nuts of fastening of a semi-axis, prepare washers, screw and tighten with demanded effort (55 ÷ 65 H • м) fixing bolts.
8. Establish a brake disk, a support and components of the parking brake (see. Head Brake system).
9. Establish wheels and lower the car on the earth. Check adjustment of the parking brake, in case of need make the corresponding adjustment (see. Head Brake system).
10. Before starting car operation, "pump over" a pedal of a foot brake before emergence of hardness at its squeezing.