Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
- Coupling and transmission line
   Specifications
   Coupling - the general information and check of a condition of components
   Removal, check of a condition and installation of components of assembly of coupling
   Removal, check of a condition and installation of the vyzhimny bearing and fork of switching off of coupling
   Check of a condition and replacement of the directing bearing
   Adjustment of a pedal of coupling
   Adjustment of a cable of a drive of coupling, removal and installation of hummock assembly (the Mirage model with a hummock drive of coupling)
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Air removal from a hydraulic path of a drive of switching off of coupling
   Removal and installation of power shafts
   Hinges of power shafts - the general information and service
   Check of a condition of the transmission line
   Removal and driveshaft installation
   Replacement of the kardanny hinge
   Driveshaft balancing
   Removal and installation of assembly of the central bearing of the driveshaft
   Removal and installation of back semi-axes (the AWD Galant model for 1993 вып.)
   Removal and installation of a stupichny pin of a back axis, wheel bearing and epiploon
   Replacement of an epiploon of a leading gear wheel of back differential
   Removal and installation a case of back differential (the AWD Galant model for 1993 вып.)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of power shafts

Removal

 PERFORMANCE ORDER

1. Not poddomkrachivy the car, take шплинты and release stupichny nuts of forward wheels.

2. To Poddomkratta the car also establish it on props.
3. On the models equipped with ABS, remove forward wheel sensors.
4. On the models equipped with Active-ECS system, release a nut of the shtutserny socket of fastening of the pneumatic line to the top part of a rack. Remove and will throw out a sealing ring. Turn out fixing bolts and remove from the top part of a rack the actuation mechanism of system. Disconnect the electroconducting brought to the activator.
5. Liberate from rotary fists spherical support of the bottom levers of a suspension bracket and tips of steering drafts.

6. Give stupichny nuts and remove washers.

7. At removal of assembly of a two-section left power shaft turn out bolts of fastening of the central basic bearing and remove the washers enclosed under their heads. By means of a stripper established from the outer side of stupichny assembly, squeeze out of the last a pin of a power shaft (at the final stage the pin is beaten out by a hammer. Knocking-out of assembly of a shaft from differential of transmission is made by means of a hammer with soft the brisk.

8. Liberation from transmission of assembly of an one-section right power shaft is made by a poddevaniye by its mount.

Attempts of a pulling of a shaft from differential are fraught with failure of the internal CV JOINT!


Installation

 PERFORMANCE ORDER

1. Replace the lock rings established on internal pins of power shafts.

2. Fill shaft in transmission, - track completeness of landing of pins.
3. Having delayed rack-mount assembly outside, fill in a nave an external pin of the corresponding power shaft.
4. Screw bolts of an arm of the central bearing and tighten them with demanded effort (45 H • м).
5. Plant on a shaft pin a washer (the party with the removed facet outside). Screw a stupichny nut, however, do not tighten it while it is final.
5. Plant a spherical support in assembly of a rotary fist. Tighten a koronchaty nut of fastening of a spherical finger with demanded effort (60 ÷ 72 H • м) also fix its new the shplinty.
6. Also plant in assembly of a rotary fist a tip of steering draft, э the koronchaty nut of a spherical finger of the hinge is tightened with effort of 29 H • m and also fixed new the shplinty.
7. On the equipped ABS models establish into place wheel sensors.
8. On models with an active suspension bracket (Active-ECS) restore initial connection of the pneumatic line (do not forget to replace a sealing ring) and fix the activator of the actuation mechanism in the top part of a rack. Connect electroconducting.
9. Operating in a similar manner, finish installation of the second power shaft.
10. Establish wheels and lower the car on the earth.
11. Tighten stupichny nuts with demanded effort (145 ÷ 188 H • м) also fix their new шплинтами.