Mitsubishi Galant

1990 — 2001 of release

Repair and car operation


Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
- Coupling and transmission line
   Specifications
   Coupling - the general information and check of a condition of components
   Removal, check of a condition and installation of components of assembly of coupling
   Removal, check of a condition and installation of the vyzhimny bearing and fork of switching off of coupling
   Check of a condition and replacement of the directing bearing
   Adjustment of a pedal of coupling
   Adjustment of a cable of a drive of coupling, removal and installation of hummock assembly (the Mirage model with a hummock drive of coupling)
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Air removal from a hydraulic path of a drive of switching off of coupling
   Removal and installation of power shafts
   Hinges of power shafts - the general information and service
   Check of a condition of the transmission line
   Removal and driveshaft installation
   Replacement of the kardanny hinge
   Driveshaft balancing
   Removal and installation of assembly of the central bearing of the driveshaft
   Removal and installation of back semi-axes (the AWD Galant model for 1993 вып.)
   Removal and installation of a stupichny pin of a back axis, wheel bearing and epiploon
   Replacement of an epiploon of a leading gear wheel of back differential
   Removal and installation a case of back differential (the AWD Galant model for 1993 вып.)
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and driveshaft installation

Design of the driveshaft of all-wheel drive models

1 — Samokontryashchayasya a nut
2 — the Rubber pillow
3 — the Remote plug

4 — the Driveshaft
N — Replace


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


2. To Poddomkratta the car also establish it on props.
3. The cranked shaft consists of three sections: forward, back and central. Release nuts of fastening of the central basic bearing and accurately take the rubber pillows established under them.

Besides rubber pillows in fixture of the bearing a number of remote plugs is used also, the quantity and which sizes can vary, - try to remember the adjusting provision of each of fixture elements.


4. Mark the provision of a krepezhnogoflanets of a back collar of the driveshaft on a connecting flange of differential of the back bridge. Turn out fixing bolts and separate a shaft from differential, - try not to damage a protective cover.

For protection of a cover against damage in it it is possible натолкать rags or the crumpled paper.

5. At driveshaft extraction from a case of a transfer case take care of preservation in an integrity and safety of an epiploon.
6. In order to avoid an oil effluence from a transfer case do not lower a car back on the earth. In a case it is meaningful to cork an opening for the purpose of the hit prevention in a dirt box.


Installation

 PERFORMANCE ORDER

1. Get the driveshaft in the regular situation and fill it in a case of a transfer case (try not to damage an epiploon).
2. Having seen to correctness of combination of the landing labels put in the course of dismantle connect a shaft to a flange of back differential. Screw fixing bolts and tighten them with demanded effort (30 ÷ 35 H • м).
3. Establish the central basic bearing (see. The section Removal and installation of assembly of the central bearing of the driveshaft), - track correctness of installation of all elements of fixture of assembly. Screw fixing nuts and tighten them with demanded effort (30 ÷ 35 H • м).
4. Check levels of liquids in a transfer case and a case of back differential.