Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Electric sockets - general information
   Protection of electric contours
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Removal and installation of the podrulevy combined switches and the switch of the lock of ignition
   Removal and installation of switches
   Removal and installation of block headlights of tight type
   Adjustment of the direction of optical axes of head headlights
   Replacement of lamps of lighting devices
   Removal and installation of a combination of devices
   Replacement of measuring instruments of a combination of devices
   Control system of speed (темпостат) - the general information and problem diagnostics
   System of additional safety (SRS) - the general information and precautionary measures
   Removal and radio tape recorder/CD-проигрывателя installation
   Removal and CD changer installation
   Removal and installation of loudspeakers
   Removal and installation of levers of screen wipers
   Removal and installation of the electromotor of a drive of screen wipers
   Schemes of electric connections - the general information
   + Schemes of electric connections


Removal and installation of the electromotor of a drive of screen wipers

The Mirage models for 1992 вып.

Forward screen wipers

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
3. Remove the forward finishing panel.
4. Remove both holders of a windscreen.
5. Having pushed inside on couple of millimeters (no more) central pins, release plastic clamps of fastening of the forward panel.
6. Remove the air inlet screen.
7. Release bolts of fastening of the electromotor of a drive of screen wipers. Disconnect from motor assembly driving draft, - in case of need remove draft from the car.

The corner of installation of the cranked lever concerning the electromotor steals up industrially in view of what these elements should not be removed without emergency. If to avoid dismantle of the lever it is not possible, previously mark adjusting provisions of components. Remove the electromotor.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place and connect to it draft of a drive of screen wipers.
2. Connect to the motor electroconducting.
3. At installation of finishing sections track reliability of a zashchelkivaniye of clamps, - the central pins should appear aflush with a panel surface. The failed fixing elements replace.
4. Establish into place levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
5. In summary connect a negative wire to the battery and check serviceability of functioning of screen wipers.


Back screen wiper

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the lever of a back screen wiper (see. Section Removal and installation of levers of screen wipers).
3. Remove big section of the panel of an internal upholstery of a door of a back (see. Head Body).
4. Disconnect electroconducting from the driving electromotor.
5. Remove the electromotor, - try not to weaken landing of the plug of a spindle of a rotary axis of the lever through passage.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place, - track, that the plug through passage appeared is developed by a label in the form of an arrow down.
2. Establish into place the screen wiper lever (see. Section Removal and installation of levers of screen wipers).
3. Connect a negative wire to the battery and check serviceability of functioning of a screen wiper.
4. In summary establish into place the panel of an internal upholstery of a door (see. Head Body).


The Mirage models since 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
3. Remove the forward finishing panel.
4. Remove both holders of a windscreen.
5. Having pushed inside on couple of millimeters (no more) central pins, release plastic clamps of fastening of the forward panel.
6. Remove the air inlet screen.
7. Release bolts of fastening of the electromotor of a drive of screen wipers. Disconnect from motor assembly driving draft, - in case of need remove draft from the car.

The corner of installation of the cranked lever concerning the electromotor steals up industrially in view of what these elements should not be removed without emergency. If to avoid dismantle of the lever it is not possible, previously mark adjusting provisions of components. Remove the electromotor.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place and connect to it draft of a drive of screen wipers.
2. Connect to the motor electroconducting.
3. At installation of finishing sections track reliability of a zashchelkivaniye of clamps, - the central pins should appear aflush with a panel surface. The failed fixing elements replace.
4. Establish into place levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
5. In summary connect a negative wire to the battery and check serviceability of functioning of screen wipers.


The Galant models for 1993 вып.

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
3. Remove the forward finishing panel.
4. Remove panels of furnish of an air inlet.
5. Uncover access openings.
6. Release bolts of fastening of the electromotor of a drive of screen wipers. Disconnect from motor assembly driving draft, - in case of need remove draft from the car.

The corner of installation of the cranked lever concerning the electromotor steals up industrially in view of what these elements should not be removed without emergency. If to avoid dismantle of the lever it is not possible, previously mark adjusting provisions of components. Remove the electromotor.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place and connect to it draft of a drive of screen wipers.
2. Connect to the motor electroconducting.
3. Establish finishing panels.
4. Establish into place levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
5. In summary connect a negative wire to the battery and check serviceability of functioning of screen wipers.


The Diamante models since 1994 вып.

Forward screen wipers

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
3. Remove the forward finishing panel.

4. Air inlet cover.
5. Disconnect from the electromotor electroconducting.
6. Uncover access openings.
7. Release bolts of fastening of the electromotor of a drive of screen wipers. Disconnect from motor assembly driving draft, - in case of need remove draft from the car.

The corner of installation of the cranked lever concerning the electromotor steals up industrially in view of what these elements should not be removed without emergency. If to avoid dismantle of the lever it is not possible, previously mark adjusting provisions of components. Remove the electromotor.



Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place and connect to it draft of a drive of screen wipers.
2. Connect to the motor electroconducting.
3. Establish into place a cover of an opening of access.
4. Establish an air inlet cover.
5. Establish the finishing panel.
6. Establish into place levers of screen wipers (see. Section Removal and installation of levers of screen wipers).
7. In summary connect a negative wire to the battery and check serviceability of functioning of screen wipers.


Back screen wiper

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the lever of a back screen wiper (see. Section Removal and installation of levers of screen wipers).
3. Remove the bottom section of the panel of an internal upholstery of a door of a back (see. Head Body).
4. Disconnect electroconducting from the driving electromotor.
5. Turn out fixing bolts and remove the electromotor.


Installation

 PERFORMANCE ORDER

1. Establish the electromotor on the regular place, - track, that the plug through passage appeared is developed by a label in the form of an arrow down.
2. Establish into place the screen wiper lever (see. Section Removal and installation of levers of screen wipers).
3. Connect a negative wire to the battery and check serviceability of functioning of a screen wiper.
4. In summary establish into place the panel of an internal upholstery of a door (see. Head Body).