The device, service, repair of Mitsubishi Galant (1990 — 2001) - Adjustment of the direction of optical axes of head headlights//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Electric sockets - general information
   Protection of electric contours
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Removal and installation of the podrulevy combined switches and the switch of the lock of ignition
   Removal and installation of switches
   Removal and installation of block headlights of tight type
   Adjustment of the direction of optical axes of head headlights
   Replacement of lamps of lighting devices
   Removal and installation of a combination of devices
   Replacement of measuring instruments of a combination of devices
   Control system of speed (темпостат) - the general information and problem diagnostics
   System of additional safety (SRS) - the general information and precautionary measures
   Removal and radio tape recorder/CD-проигрывателя installation
   Removal and CD changer installation
   Removal and installation of loudspeakers
   Removal and installation of levers of screen wipers
   Removal and installation of the electromotor of a drive of screen wipers
   Schemes of electric connections - the general information
   + Schemes of electric connections





Adjustment of the direction of optical axes of head headlights

The scheme of an arrangement of screws of adjustment of the direction of optical axes of block headlights of the combined type

1 — the Screw of a regulriovka of provision of a headlight in the vertical plane

2 — the Screw of a regulriovka of provision of a headlight in the horizontal plane


 PERFORMANCE ORDER

Violation of adjustment of the direction of optical axes of head headlights can lead to dazzle of drivers of vehicles moving by a parallel course and to be at the bottom of emergency creation on the road. Check of correctness of adjustment of headlights should a proizlirovka of optical axes should be made in the conditions of a specialized workshop of car-care center!

1. The scheme of an arrangement of screws of adjustment of provision of block headlights is shown on illustrations.

2. There are some methods of check of correctness of adjustment of the direction of optical axes of head headlights of the car. Simplest of them, not demanding from the performer of any special skills and not needing use of the special equipment below is described.
3. Drive the car a front to a wall. Paste on a wall an adhesive tape strip on the vertical line passing in the diametrical plane of the car. Also paste vertical strips of an adhesive tape on the lines passing through the centers of projections to a wall of lenses of head headlights.
4. Paste on a wall horizontally located strip of an adhesive tape on the line which has been carried out through the centers of projections of lenses of head headlights on a surface of a wall.

This procedure is simpler for making, having adjusted the car closely to a wall.

5. For performance of adjustment of the direction of optical axes of head headlights roll away the car from a wall on distance about 7.6 m.

The platform on which the car takes place, should have an equal horizontal surface, it is desirable with a firm covering. The fuel tank of the car should be filled half, from salon and a luggage compartment all heavy subjects breaking centering of the car are taken.


6. Begin with adjustment of the direction of an optical axis of a passing beam. Try to achieve rotation of adjusting screws of block headlights of such arrangement of light spots that zones with the maximum intensity of lighting it appeared approximately in 50 mm is lower than the horizontal line and on a touch size more to the right of the vertical.

7. Having finished the first adjustment, include a driving beam: zones of the maximum intensity of illumination should be displaced in the direction of crossing of vertical lines with horizontal, having appeared is slightly lower than the last.

To receive equally complete centering of beams both near, and a driving beam in practice it is not obviously possible. It is necessary to try to achieve some compromise solution taking into account features of operation of the car, keeping in head of a corner aspiration to provide the maximum traffic safety.

8. At the first possibility drive away the car on car repair shop for performance of adjustment of the direction of optical axes of head headlights with use of the special equipment.