Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
- Engine electric equipment
   Specifications
   Engine start from the auxiliary power supply
   Removal and installation of the storage battery
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and precautionary measures
   Serviceability check functioning/adjustment of system of ignition
   Check of a condition and coil replacement (ек) ignitions
   Removal and installation of the key transistor (ignition module)
   Removal and installation of the distributor of ignition (model with contactless system of ignition)
   Removal and installation of sensors of provision of cranked and distributive shaft
   Check and adjustment of installation of a corner of an advancing of ignition
   Ignition order
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Check of serviceability of functioning, removal and generator installation
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of the distributor of ignition (model with contactless system of ignition)

Removal

 PERFORMANCE ORDER

1. Bring the engine into the provision VMT of the end of a step of compression of the piston of the first cylinder, - be guided on adjusting labels of cogwheels of a drive of GRM (see. Head Engine).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. At the corresponding complete set remove a protective cover of a plait of VV of electroconducting.
4. Disconnect from the distributor electroconducting, give a fixing bolt and take away an electroconducting plait with the condenser connected to it aside.

5. Uncover the distributor with VV connected to it wires.
6. In case of need disconnect a bobbin wire.
7. Mark situation a begunka concerning the case of the distributor and position of the case concerning the engine.

8. Give a clamping nut.

9. Carefully remove the distributor from the engine.


Installation

Adjusting labels are combined (the engine was not turned)

 PERFORMANCE ORDER

1. Having slightly greased with pure lubricating oil, establish on the distributor a new sealing ring.
2. Establish the distributor on the engine, - track correctness of combination of landing labels (cases and a begunka). Make sure of completeness of landing of the distributor and introduction of its power shaft in gearing.
3. Screw a clamping nut.
4. Connect to the distributor electroconducting and fix a plait a special bolt.
5. Establish on the distributor a cover with VV connected to it wires.
6. Connect a negative wire to the battery.
7. Make adjustment of installation of a corner of an advancing of ignition (see. The section Check/adjustment of installation of a corner of an advancing of ignition), then finally tighten a clamping nut with demanded effort (11 H • м).

Adjusting labels рассовмещены (the engine was turned at the removed distributor)

 PERFORMANCE ORDER

1. Establish on the distributor a new sealing ring.

2. Bring the engine into the provision VMT of the end of a step of compression of the first cylinder, - be guided on combination of adjusting labels of cogwheels of a drive of GRM (see. Head Engine). Track also that the label on a damper of krutilny fluctuations appeared opposite to a zero mark of a scale of the index.

3. Having tracked correctness of combination of the components of landing labels put in the course of dismantle, establish the distributor on the engine, - the directing pin should get to a reciprocal groove of a landing flange. Make sure of completeness of landing of assembly and that will develop a begunok a nouse towards an arrangement of the plug of the first cylinder on a cover (on a case rim at dismantle the landing label) was put.