Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
- Engine electric equipment
   Specifications
   Engine start from the auxiliary power supply
   Removal and installation of the storage battery
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and precautionary measures
   Serviceability check functioning/adjustment of system of ignition
   Check of a condition and coil replacement (ек) ignitions
   Removal and installation of the key transistor (ignition module)
   Removal and installation of the distributor of ignition (model with contactless system of ignition)
   Removal and installation of sensors of provision of cranked and distributive shaft
   Check and adjustment of installation of a corner of an advancing of ignition
   Ignition order
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Check of serviceability of functioning, removal and generator installation
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Check of a condition and replacement of wires of the battery

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

Cars of considered model are equipped with the SRS system which main component are the safety cushion which is disconnecting later rather short time after a detachment of wires from the battery. If the control lamp of SRS after connection of the battery lights up and remains included, the car should be driven away on car repair shop for the purpose of SRS activation.


 PERFORMANCE ORDER

1. Regularly examine battery wires on all their length on existence of signs of mechanical damages, cracks and прогаров isolation, and also corrosion traces. Do not forget that violation of quality of electric connection of contact plugs is capable to lead to difficulties at engine start, and also to decrease in efficiency of its return.
2. Check terminal clips of wires on existence of cracks, signs of loss of copper veins and corrosion traces. Presence accumulated under the insulation layer near terminal tips of white poroshkoobrazny deposits speaks about development of corrosion and need of replacement of a wire. Check plugs of the battery and clips of fastening of tips of wires on them on existence of signs of deformation, weakening of bolts and corrosion traces.
3. The negative wire is always disconnected from the battery first of all and connected in the last. Do not forget to disconnect a negative wire even in case only one positive is subject to replacement.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for equipment introduction in action!

4. Disconnect from the battery old wires (at first negative), then "walk" on each of them till the opposite end disconnect from the traction relay of a starter (positive) and plugs grounding (negative). Try to remember routes of laying of both wires for the purpose of observance them at installation of the new.
5. Make sure that replaceable wires correspond on a standard size removed from the car. Take a wire subject to replacement with itself in shop as an example. Extremely important factor is compliance of a design of clips of a wire to a form of connecting plugs on the car.

Wires are easy for distinguishing from each other on color of isolation, always black at negative, and red at the positive. Besides, the positive wire usually has bigger section.

6. A wire brush smooth out a carving on connecting plugs of the traction relay and grounding. After removal of all traces of corrosion slightly grease carving rounds with acid-free vaseline for the purpose of prevention of development of corrosion further.
7. Connect a wire to the plug of the traction relay/weight, strongly tighten fixing a nut/bolt.
8. Before connecting a new wire to the polar plug of the battery make sure that it freely reaches it without an excessive tension. Carefully smooth out polar plugs of the battery, then slightly grease them with acid-free vaseline.
9. First of all always connect to the battery a positive wire, then negative.