The device, service, repair of Mitsubishi Galant (1990 — 2001) - Removal and installation of door glass and a window regulator regulator//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of lateral doors
   Removal, installation and adjustment of provision of a cowl
   Removal, installation and adjustment of provision of a door of a back (Hatchback models and Versatile person)
   Removal, installation and adjustment of provision of a cover of a luggage compartment (Sedan model)
   Removal and installation of door rear-view mirrors
   Replacement of the aerial of a radio receiver
   Removal and installation of forward wings
   Removal and dashboard installation
   Removal and installation of the central console
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of the external handle of a door and elements of a drive of a latch of the lock
   Removal and installation of the cylinder of the lock of a lateral door
   Removal and installation of the cylinder of the lock of a door of a back/cover of a luggage compartment
   Removal and installation of the handle of a door of a back
   Removal and installation of door glass and window regulator regulator
   Removal and installation of the electromotor of a drive of a window regulator
   Replacement of a salonny rear-view mirror
   Removal and installation of seats
   Removal and installation of the electromotor of a drive of a seat
+ Onboard electric equipment





Removal and installation of door glass and window regulator regulator

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Lower door glass in extreme bottom situation.
3. Remove the panel of an internal upholstery and the insulating screen of a door.
4. Hooking edge of a piece of a fabric, carefully separate from a doorframe a tape molding.
5. Remove internal stabilizers of glass.
6. On forward doors remove directing ползун.

7. Prop up bottom edge of glass, then turn out two bolts of fastening of glass to a window regulator regulator, - not propped up glass can fail in a doorframe.

8. Accurately take glass from a doorframe through a window aperture.
9. Turn out bolts of fastening of a regulator.

10. At the corresponding complete set disconnect electroconducting from the electromotor of a drive of a window regulator.
11. Take a regulator through a special window of access in a doorframe.


Installation

 PERFORMANCE ORDER

1. Before installation it is necessary to grease moving elements of a regulator with universal greasing slightly.
2. Establish a regulator on the regular place and by hand tighten fixing bolts.
3. Since the left bottom bolt and moving clockwise, make a final tightening of fixture of a regulator.
4. At the corresponding complete set connect electroconducting to the driving electromotor.
5. Fill in a doorframe a windowpane and fix it on a regulator.

On the Hatchback models the back support of glass, on models a sedan - a lobby first of all is tightened.

6. Slowly closing a window, check correctness of an arrangement of glass in a doorframe aperture. In case of need remove a regulator and slightly develop the openings provided in it under bolts of fastening of glass, - previously make sure that the distortion of glass is not connected with deformation of elements of a regulator.
7. Establish other components of a doorframe acting in film for the purpose of ensuring access.
8. Connect a negative wire to the battery.