Mitsubishi Galant

1990 — 2001 of release

Repair and car operation

Cocktail

Removal and installation of the central console

Details of installation of sections of the central console on the Mirage models for 1992 вып.


1 — the Coin box 2 — the Pocket 3 — the Switch of management of the electric drive door mirrors/cap 4 — Facing	5 — Back section of console assembly 6 — the Handle of the lever of gear shifting (RKPP) 7 — Forward section of console assembly

Details of installation of sections of the central console on the Mirage 1993 ÷ 1996 models of вып.


1 — the Finishing panel 2 — the Cap 3 — the Cap 4 — Facing 5 — the Directing frame	6 — Back section of console assembly 7 — the lever Handle switching I transfers (RKPP) 8 — the Clamp 9 — Forward section of console assembly 10 — the Basic arm

Details of installation of sections of the central console on the Mirage models since 1997 вып.


1 — Back section of console assembly 2 — the Ashtray 3 — the Panel of facing of a radio tape recorder 4 — Forward section of console assembly	5 — the Facing panel of the lever of the selector (AT) 6 — Forward section of console assembly 7 — the Basic arm

Details of installation of sections of the central console on the Galant models for 1993 вып.


1 — the Facing panel of the lever of gear shifting (RKPP) 2 — the Protective cover of the lever of gear shifting 3 — the Coaster 4 — the Console ware box 5 — the Cover of a console ware box 6 — Loopy clamps	7 — the Switch of management of functioning of the electric drive of door mirrors 8 — the Switch of modes of movement a POWER/ECONO/cap 9 — the Switch of electronic control by hydrostrengthening system a wheel/cap 10 — the Finishing panel 11 — Basic arms

Details of installation of sections of the central console on the Galant 1994 ÷ 1998 models of вып.


1 — the Handle of the lever of gear shifting (RKPP) 2 — the Panel of facing of the lever of gear shifting 3 — the Pocket 4 — the Central (console) section of furnish of the dashboard	5 — Forward section of console assembly 6 — the Basic arm And 7 — the Basic arm In

Details of installation of sections of the central console on the Galant models since 1999 вып.


1 — Facing of the lever of gear shifting 2 — the Coaster (models without armrests) 3 — the Armrest (models with armrests) 4 — the Basic arm And (models to be with armrests) 5 — Console assembly	6 — the Bottom central panel of furnish 7 — the Ashtray 8 — the Basic arm With 9 — the Basic arm And

Details of installation of sections of the central console on the Diamante 1992 ÷ 1996 models of вып.


1 — the Ashtray/panel of switches 2 — the Switch/cap	3 — Console assembly

Details of installation of sections of the central console on the Diamante models since 1997 вып.


1 — the Coaster 2 — the Coin box 3 — the Finishing panel 4 — Lateral covers	5 — Console assembly 6 — the Basic arm And 7 — the Basic arm With

Back section

Removal

PERFORMANCE ORDER

1. Details of installation of back section of the central console are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!
On the models equipped with a pillow (Omiya) to safety, wrap up a wire tip an insulating tape and start to work not less than 60 seconds during which should occur SRS shutdowns later!

3. Open a cover of a console ware box.
4. In case of need unbend carpet edge in the lower part of console assembly.
5. Turn out the fixing screws located along bottom, which of back section of console assembly.
6. In case of need Remove caps and turn out forward fixing screws.
7. Lift the console and take it from the car.

On some models seat belts are passed through console assembly and they are necessary for liberating accurately from it.

Installation

PERFORMANCE ORDER

Installation is made upside-down.

Forward section

Removal

PERFORMANCE ORDER

1. Details of installation of forward section of the central console are shown on illustrations.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!
On the models equipped with a pillow (Omiya) to safety, wrap up a wire tip an insulating tape and start to work not less than 60 seconds during which should occur SRS shutdowns later!

3. In case of need remove back section of the console.
4. In case of need remove an ashtray and a coaster.
5. In case of need remove carpet inserts of console assembly.
6. On models from RKPP remove the handle from the gear shifting lever.
7. On models from AT remove the facing panel of the lever of the selector.
8. Remove caps, turn out fixing screws and remove lateral covers of the console.
9. Remove caps of forward fixing screws.
10. Previously having marked, disconnect all electroconducting brought to console assembly.
11. Turn out fixing screws and remove console assembly.

Installation

PERFORMANCE ORDER

Installation is made upside-down.