The device, service, repair of Mitsubishi Galant (1990 — 2001) - Removal and installation of assembly of the control panel by functioning of a heater and the air conditioner, adjustment of driving cables//Mitsubisi Galant /

Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
- Cooling and heating systems
   Specifications
   Antifreeze - general information
   Check of serviceability of functioning and thermostat
   Check of a condition of the fan of system of cooling
   Removal and installation of a radiator of system of cooling
   Check of a condition of the water pump
   Removal and installation of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
   Replacement of the electromotor of a drive of the fan of a heater
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of driving cables
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of driving cables

Cars considered in the real Management are equipped with system of additional safety of SRS which is better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid receiving traumas as a result of its casual operation, - disconnect from the battery at first negative, then for a positive wire and wait not less than two minutes before starting service of the components located near sensors of directed overloads (see. Head Onboard electric equipment). Isolation and contact sockets of electroconducting of a chain of SRS are painted in bright yellow color. It is not necessary to connect any diagnostic devices to this chain!


Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Release clamps and remove the central section of furnish of the dashboard (see. Head Body).

3. Remove the radio tape recorder/CD player.

4. Turn out screws of fastening of the control panel functioning of the heater/conditioner of air Wring out a lever finger and disconnect a cable of a damper of switching of distribution of air. Disconnect other driving cables and electroconducting. By means of nippers release a clamp and remove control panel assembly from the car.


Installation

 PERFORMANCE ORDER

1. Transfer the handle of a choice of a temperature mode to situation MOVE NOTES (the maximum heating).
2. The driving lever of a distributing damper on heater assembly also transfer to situation MOVE NOTES, then connect to a lever finger a driving cable.
3. Delay a cable cover in the direction specified by a markerny arrow, having provided assembly a necessary weak point, then fix a cable by means of a clip.
4. Transfer the handle of a choice of the direction of distribution of air to situation обдува a windscreen (DEF). In the same situation establish the driving lever of the corresponding damper on heater assembly, then connect to a lever finger a driving cable.
5. Delay a cable cover in the direction specified by a markerny arrow, having provided assembly a necessary weak point, then fix a cable by means of a clip.
6. Transfer the lever of a choice of a mode of air circulation to control panels in a mode of the closed circulation. To the relevant situation transfer the driving lever of the corresponding damper on heater assembly. Connect a cable to a lever finger.
7. Delay a cable cover in the direction specified by a markerny arrow, having provided assembly a necessary weak point, then fix a cable by means of a clip.
8. Correctly place management assembly on the dashboard. Return and strongly tighten fixing screws.
9. Establish a clamp.
10. Connect a negative wire to the battery and check serviceability of functioning of central air of air.
11. Establish into place an autoradio tape recorder / компакт-проигрыватель.
12. Establish the central section of furnish of the dashboard (track reliability of a zashchelkivaniye of all provided clamps). Screw and tighten fixing screws.


Adjustment of driving cables

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Transfer the handle of the selector of a choice of the direction of distribution of air to situation обдува a windscreen. Shift the lever of the corresponding damper against the stop inside and connect to it a driving cable. Adjust a cable tightness.
3. Transfer the lever of a choice of a mode of air circulation to the provision of the closed circulation. Shift against the stop inside a dempferny zaslonka and connect a cable to the driving lever. In a demanded way adjust a tightness.