Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
- Settings and routine maintenance
   Schedule of routine maintenance of Mitsubishi Galant/Mirage/Diamante cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Replacement of impellent oil and oil filter
   Check, service and charging of the storage battery
   Check of a condition of components of system of cooling
   Check of a condition and replacement of the hoses located in an impellent compartment
   Check of a condition and replacement of brushes of screen wipers
   Rotation of wheels
   Check of a condition of components of a suspension bracket and steering drive
   Greasing of components of the chassis
   Replacement of ATF of automatic transmission and differential of the main transfer, check of a condition and AT filter service
   Check of a condition of brake lines
   Check condition/service of disk brake mechanisms
   Check of a condition of protective covers of power shafts
   Check and adjustment of gaps of valves - only Mirage
   Replacement of a filtering element of an air purifier
   Service of system of cooling
   Replacement of the fuel filter
   Check and replacement of the valve of system of operated ventilation of a case (PCV)
   Check of a condition and replacement of spark plugs
   Condition check, adjustment of effort of a tension and replacement of driving belts
   Check of a condition of components of system of production of the fulfilled gases
   RKPP transmission oil replacement
   Replacement of greasing of a transfer case - only all-wheel drive Galant
   Replacement of greasing of back differential - only all-wheel drive Galant
   Check condition/service of drum-type brake mechanisms
   Check of serviceability of functioning of the parking brake
   Check of serviceability of functioning of the vacuum amplifier of brakes
   Check of a condition of seat belts
   Check of a condition and replacement of components of system of ignition
   Check/adjustment of installation of a corner of an advancing of ignition
   Check of a condition of components of system of catching of fuel evaporations
   Check of a condition of components of a power supply system
   Check of a condition and belt replacement GRM drive (it)
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Check and adjustment of gaps of valves - only Mirage

 PERFORMANCE ORDER

Regular adjustment of klapanny gaps is made only on Mirage models of 1.5 l of 1990 ÷ 1995 вып. and 1.8 l of 1993 ÷ 1995 вып.

Violation of adjustment of klapanny gaps to increase of the noise background, made klapanny the mechanism and violation of stability of turns of the engine. Check and adjustment of klapanny gaps should be made on the heated-up engine to normal working temperature!

1. Warm up the engine to normal working temperature, muffle it and disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. For the purpose of simplification of a provorachivaniye of the engine manually turn out spark plugs.
3. Uncover heads of cylinders.
4. Having turned a cranked shaft clockwise, achieve combination adjusting risks on a pulley with a mark T in the bottom cover of a gas-distributing belt, - pistons of the 1st and 4th cylinders should appear in provisions VMT. Подвигав yokes of a drive of valves of the 1st and 4th cylinders up-down, define, which piston from cylinders occupies the provision VMT of the end of a step of compression (both yokes will freely move).

5. With the help щупа lezviyny type measure size of klapanny gaps. In the provision VMT of the end of a step of compression of the piston of the 1st cylinder measurement of gaps inlet and final valves of the 1st and 2nd cylinders is made. Then the cranked shaft should be turned on one complete revolution clockwise for the purpose of reduction in VMT of the end of a step of compression of the piston of the 4th cylinder and measurement of gaps inlet and final valves of the 3rd and 4th cylinders.

6. Compare results of measurements to requirements of Specifications. In case of need weaken a lock-nut of a yoke of a drive of the corresponding valve and make installation of its gap by means of the adjusting screw. Having achieved demanded result, tighten a lock-nut with demanded effort (12 ÷ 15 H • m for models 1.5 of l/9 of H • m for models of 1.8 l), - track, that in the course of a nut tightening position of the screw did not change.
7. Establish into place a cover of a head of cylinders, screw spark plugs and connect a negative wire to the battery.