Mitsubishi Galant + Identification numbers of the car + Governing bodies + Settings and routine maintenance + Engine + cooling and heating Systems + Power supply system and release + engine Electric equipment + Control systems of the engine - Manual transmission + 5-step manual box of gear shifting (RKPP) - Automatic transmissions (AT) General information and functioning principle AT problem diagnostics - the general information The adjustments made without removal of AT from the car Removal and installation of the pallet of a case of AT Removal, installation and adjustment of the sensor switch of permission of start Removal and AT installation Major maintenance of AT + Transfer case + Coupling and transmission line + Brake system + Suspension bracket and steering + Body + Onboard electric equipment
|
Removal, installation and adjustment of the sensor switch of permission of start
The Mirage models for 1997 вып. and Galant for 1993 вып.
Removal
|
1. Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Disconnect from the lever a driving cable of the AT selector.
|
3. Turn out two fixing screws and remove the sensor switch. |
|
|
Installation
|
1. Establish the sensor switch on the regular place. Screw fixing bolts, however do not tighten them before completion of adjustment of the sensor switch. 2. Connect to the sensor switch electroconducting and make its adjustment (see below). 3. Connect a negative wire to the battery. 4. Make sure that start of the engine is obviously possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
Adjustment
|
1. Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Cock the parking brake and prop up car wheels protivootkatny boots. 3. Find established from above on a transmission case the sensor switch of permission of start. 4. Weaken an adjusting nut of a cable of a drive of switching on a transmission case. In salon of the car transfer the selector lever to the situation "N". 5. A manual control lever transmission switching also transfer to the situation "N". 6. Release screws of fastening of the sensor switch and develop the last so that the 5-millimetric opening in its case was combined with a reciprocal opening (also 5-миллимитровым) in the manual lever of switching. 7. Tighten bolts of fastening of the sensor switch with demanded effort (10 ÷ 12H • м). 8. Having delayed a driving cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort of 12 H • m. 9. Make sure that the sensor switch lever when switching AT modes from salon moves to the relevant situation. 10. Connect a negative wire to the battery. 11. Make sure that start of the engine is possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
The Galant models since 1994 вып. and Mirage since 1998 вып.
Removal
|
1. The sensor switch of permission of start on these models also is from above on a transmission case. 2. Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
3. Disconnect from the lever a driving cable of the AT selector. 4. Give a nut of fastening of a driving cable of management of transmission switching to the manual lever of transmission. Take a cable aside. 5. Transfer the manual lever to the situation "N", then give a nut on the lever. 6. Disconnect electroconducting from the sensor switch of permission of start. 7. Turn out fixing bolts and remove the sensor switch. |
|
Installation
|
1. Establish the sensor switch on the regular place. Screw, but do not tighten while fixing bolts. 2. Connect to the sensor switch the manual lever and fix it a nut, - track, that the lever remained in the situation "N". 3. Execute sensor switch adjustment (see below), then finally tighten bolts of fastening of the sensor switch with demanded effort (11 H • м). 4. Connect to the sensor switch electroconducting. 5. Connect a cable of a drive of switching, choose its weak point, check freedom of moving of the lever and tighten a nut of fastening of a cable. 6. Connect a negative wire to the battery. 7. Make sure that start of the engine is obviously possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
Adjustment
|
1. Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Cock the parking brake and prop up car wheels protivootkatny boots. 3. Find established from above on a transmission case the sensor switch of permission of start. 4. Weaken an adjusting nut of a cable of a drive of switching on a transmission case. In salon of the car transfer the selector lever to the situation "N". 5. A manual control lever transmission switching also transfer to the situation "N". 6. Release screws of fastening of the sensor switch and develop the last so that the 5-millimetric opening in its case was combined with a reciprocal opening (also 5-миллимитровым) in the manual lever of switching, - pass in openings a drill of suitable diameter and tighten bolts of fastening of the sensor switch with demanded effort (11 H • м). 7. Having delayed a driving cable around an adjusting nut, completely choose its weak point, then tighten a nut with effort of 12 H • m. 8. Check freedom of a course of the manual lever. 9. Connect a negative wire to the battery. 10. Make sure that start of the engine is possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
Diamante models
Removal
|
|
1. Location of the sensor switch is shown on an illustration.
|
2. Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
3. Turn out two fixing bolts and remove the sensor switch. |
|
Installation
|
1. Establish the sensor switch on the regular place. Screw, but do not tighten while fixing bolts. 2. Execute sensor switch adjustment (see below), then finally tighten bolts of fastening of the sensor switch with demanded effort (10 ÷ 12 H • м). 3. Connect a cable of a drive of switching. 4. Connect a negative wire to the battery. 5. Connect to the sensor switch electroconducting. 6. Make sure that start of the engine is possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
Adjustment
|
1. Adjustment, as well as earlier, is made by combination of 5-millimetric openings in the case of the sensor switch and a body of the manual lever of a drive of switching. 2. In summary make sure that start of the engine is possible only in the transmission provisions "R" and "N". Also check serviceability of operation of fires of a backing at transfer of the lever of the selector to the situation "R". |
|
|
|