Mitsubishi Galant + Identification numbers of the car - Governing bodies Access, protection Seats and safety devices Instrumentations and governing bodies Comfort Operation receptions + Settings and routine maintenance + Engine + cooling and heating Systems + Power supply system and release + engine Electric equipment + Control systems of the engine + Manual transmission + Coupling and transmission line + Brake system + Suspension bracket and steering + Body + Onboard electric equipment
|
Comfort
Standard control panel functioning of systems of heating, ventilation and air conditioning
Adjustment of intensity and the direction of distribution of an air stream via the central deflectors of the dashboard
Systems of heating, ventilation and air conditioning
At the correct use of possibilities of systems of heating and ventilation in salon of the car comfortable conditions of stay are provided and the zapotevaniye of glasses is excluded.
If the car upon purchase was not equipped with air central air, it can be mounted and established during any time convenient for the owner, at any time establish this system on the car, - address on Mitsubishi company car repair shop.
Standard control panel functioning of systems of ventilation, heating and air conditioning
The general view of the control panel with the indication of an arrangement of handles is presented on an accompanying illustration.
Handle of a choice of a high-speed mode of the fan
Handle rotation clockwise leads to increase in frequency of rotation of the fan and, therefore, - intensity of supply of air in car salon. Transfer of the handle to extreme left situation leads to fan shutdown.
Handle of a regulator of air temperature
Handle rotation clockwise leads to increase in temperature of the car of air arriving in salon.
Switch of the conditioner of air
The button is intended for inclusion and switching off of the conditioner of air. At turning on of the conditioner the control lamp built in the button lights up. Shutdown To/in is made by repeated pressing of the button (the control lamp should go out).
Switch of a mode of air circulation
By means of this button inclusion of a mode of air circulation in car salon is made. The button is equipped with the built-in control lamp. At mode inclusion the salon of the car is isolated from environment and inflow to it fresh air stops. The fan provides air circulation on the closed contour. By repeated pressing the button (the control lamp should go out), supply of fresh air in salon will renew. The mode is intended for fast warming up/cooling of the car which was in salon of air, and also can join in journey time through zones with badly smelling air.
|
It is not necessary to include a circulation mode for a long time as air thus quickly becomes stale. |
Handle of switching of the directions of distribution of air
|
1. The handle is intended for a choice of a mode of distribution of air on salon.
|
Supply of air via lateral deflectors of the dashboard is carried out in all modes. The general scheme of distribution of an air stream is presented on an illustration. |
|
2. The scheme of distribution of air according to a choice of a mode is presented in the table.
|
Via the central and lateral deflectors air moves irrespective of position of the handle. |
Mode choice
Deflectors through which supply of air is carried out
Supply of air in the top part of salon
Supply of air in the top part of salon and in foot wells
Supply of air in foot wells
Supply of air in foot wells and on having blown wind and lateral glasses
Supply of air on having blown in glasses
Management of deflectors of ventilating lattices
Adjustment of intensity and the direction of distribution of an air stream via lateral deflectors of the dashboard
Deflectors of the central and lateral air lines of the dashboard are equipped with special rotary zhalyuziyny lattices, besides deflectors are capable to turn rather horizontal axis that allows allowing to regulate the direction of giving of an air stream both in horizontal, and in vertical the planes. Management of deflectors is carried out by means of built in a lattice snuffled rychazhok, intensity of supply of air gets out built in deflector facing by a ring regulator.
Instructions on use of systems of ventilation, heating and air conditioning
Below detailed maintenance instructions of systems of heating, ventilation and air conditioning are provided in various climatic conditions. Information on is presented to attention of the reader how to provide effective ventilation, heating and air cooling in car salon, and also how quickly to remove from glasses condensate and hoarfrost.
All considered systems function only at the started engine. As a working body for a heater cooling liquid of the engine is used. If the engine is not heated-up to normal working temperature, some minutes before in salon warm air will start to move is required. Work of central air of air does not depend on temperature of cooling liquid of the engine.
In absolute majority of cases the best efficiency of functioning of the systems providing a comfortable microclimate, is reached in a giving mode in salon of external air. Long inclusion of a mode of the closed circulation, especially at the idle conditioner of air, leads to a zapotevaniye of glasses and increase of a spertost of air therefore it is recommended to include this mode only in case of need and for rather short time, for example, at movement on the district with the filled with smoke or polluted atmosphere. As soon as need of isolation of salon will disappear, giving in salon of fresh air should be renewed.
External atmospheric air arrives in heating and conditioning systems through the reception lattice located before a windscreen and equipped with a fairing. Periodically clean openings of a reception lattice from leaves and the other garbage complicating passing of air.
Ventilation of salon of the car
The system of a supply and exhaust ventilation provides a constant exchange of air in car salon. The fresh external air arriving through a forward reception lattice, circulates on salon and then is removed through the exhaust outlets located near back glass:
a) Turn the handle of a regulator of air temperature counter-clockwise against the stop. Check, that the conditioner of air was switched off; b) Establish the handle of switching of the directions of supply of air in situation. The mode of air circulation should be switched off; c) By means of the handle of a choice of a high-speed mode of the fan establish demanded intensity of supply of air in car salon.
Air cooling in car salon
Cooling of salon is made as follows:
a) Turn on the air conditioner, having pressed the A/C button, - the control lamp built in the switch should light up; b) Check, that the handle of a regulator of air temperature was turned in extreme left situation. c) Establish the handle of switching of the directions of supply of air in situation; d) At high humidity of external air include a circulation mode, at low humidity, - a mode of inflow of fresh air; e) By means of the handle of a choice of a high-speed mode of the fan establish demanded intensity of supply of air in salon.
If the car staid a long time on the sun and air in salon strongly heated up, quickly to reduce temperature in salon as follows:
a) Start the engine; b) Turn on the air conditioner. Check, that the handle of a regulator of air temperature was turned in extreme left situation; c) By means of the handle of a choice of a high-speed mode of the fan establish the maximum intensity of supply of air in salon; d) Partially slightly open windows and turn the handle of switching of the direction of distribution of air in situation. Include a mode of inflow of fresh air.
After air temperature in salon will decrease to acceptable level, close windows and establish a normal mode of air conditioning (see above).
Work of central air of air leads to increase of load of the car engine therefore it is necessary to watch closely an arrow of the index of temperature of cooling liquid (see. The section Instrumentations and governing bodies), moving with frequent stops and on small speed in the conditions of an intense city cycle, or overcoming long liftings of a considerable steepness. At approach of an arrow of the index to a red range of a scale, temporarily switch off the air conditioner until the temperature of the engine will not return to norm.
Heating of salon of the car
To lift air temperature in car salon, execute the following manipulations:
a) Start the engine; b) Establish the handle of switching of the directions of distribution of air in situation. The mode of air circulation should be switched off; c) By means of the handle of a choice of a high-speed mode of the fan establish demanded intensity of supply of air in salon; d) Turning the handle of a regulator of air temperature in this or that party, establish desirable degree of heating of air.
Salon heating with simultaneous drainage of air by means of the conditioner
At central air work humidity of air in salon of the car decreases, therefore simultaneous inclusion of systems of heating and conditioning allows to make air in car salon warm and dry:
a) Turn on the fan; b) Turn on the air conditioner; c) Establish the handle of switching of the directions of distribution of air in situation. The mode of air circulation should be switched off. d) Turning the handle of a regulator of air temperature in this or that party, establish desirable degree of heating of air arriving in salon. In this mode cold air from the conditioner mixes up with warm air from a heater.
Joint inclusion of systems of heating and air conditioning can be applied in any traffic conditions when the temperature of air is higher 0°Ñ.
Removal from condensate and hoarfrost glasses
To clear internal surfaces of glasses of the condensed moisture it is possible as follows:
a) Turn on the fan; b) At the corresponding complete set of the car turn on the air conditioner; c) Establish the handle of switching of the directions of distribution of air in situation.rezhy to air circulation it should be switched off. Some options of execution of the car provide possibility of automatic inclusion of a mode of supply of fresh air and its conditioner by installation of the handle of switching of the directions of distribution of air in situation; d) Turn the handle of a regulator of air temperature in such situation that warm air moved through nozzles îáäóâà a windscreen; e) Include an electroheater of back glass for faster removal of the condensed moisture from its surface. On some options of execution of the car if the handle of switching of the directions of distribution of air is in any situation except, the conditioner of air remains included. For switching off of the conditioner press the À/Ñ button.
To remove from an external surface wind and lateral glasses hoarfrost or the ice formed after parking of the car on the street in frosty weather, execute the following manipulations:
a) Include ignition, having turned a key in the lock in the situation "ON" (II); b) Establish the handle of switching of the directions of distribution of air in situation. The mode of air circulation should be switched off. Some options of execution of the car provide possibility of automatic inclusion of a mode of supply of fresh air and the conditioner, by installation of the handle of switching of modes of the direction of distribution in situation; c) Turn the handle of a regulator of air temperature in extreme right situation (the maximum heating of air) and turn on the fan for the maximum speed; d) Start the car engine.
For acceleration of cleaning of a windscreen from hoarfrost or ice it is recommended to include a mode of the closed air circulation in very cold weather at first. After the windscreen will be released from fly, renew supply of fresh air for the purpose of prevention of a zapotevaniye of glasses.
In a mode îáäóâà glasses all submitted to salon of air arrives through the slot-hole nozzles located from above on the dashboard at the basis of a windscreen, and also via lateral ventilating deflectors of the dashboard. The air temperature, blowing glass, and speed of purification of glasses increase in process of engine warming up. For acceleration of process of removal from a windscreen of condensate, hoarfrost or ice it is possible to close lateral ventilating deflectors. In this case all air will go only on having blown in a windscreen.
For reasons of safety it is not necessary to begin movement until all windows of the car will not be cleared of condensate, and to the driver the adequate review will not be provided.
Switching off of systems of heating and ventilation
Temporarily to disconnect heating and ventilation systems, turn handles of regulators of a high-speed mode of the fan and air temperature in the extreme left provisions.
Need for shutdown of systems arises in the first some minutes after engine start in cold weather as it provides faster warming up of the engine to temperature, sufficient for effective functioning of a heater. In all other cases keep the fan constantly included in avoidance of a stagnation of air in salon.
Climate control system
Scheme of an arrangement of external information sensors of system of climate control
|
The system of climate control can enter into a standard complete set of some models and carries out functions of management by ventilation, heating and air conditioning in salon. The heater and the conditioner provide maintenance of the set air temperature in salon, being guided by indications of information sensors of temperature and radiation. Besides, the system climate-kotrolya automatically carries out a choice of a high-speed mode of the fan and makes distribution of distribution of air depending on the set temperature.
|
The chosen temperature mode remains in memory of the control unit of system of climate control, however from there will be erased at a detachment of a negative wire from the battery (by default at restoration of a food by system the maintenance mode in temperature salon 25.0°Ñ will be chosen). |
|
The direction of streams of the air arriving in salon from the central and lateral ventilating snuffled, it can be adjusted manually, by means of mobile lattices of deflectors, - rychazhka of management are located in the middle of deflektorny lattices. At desire, supply of air via lateral deflectors of the dashboard can be completely stopped.
System functioning in an automatic mode
The control panel functioning of systems of heating, ventilation and air conditioning on the models equipped with system of climate control
Transfer of system of climate control to an automatic mode of functioning by a nazhimaniye on the AUTO button on the control panel. Rotation of the handle of a regulator of temperature (TEMP) establish desirable air temperature.
The system automatically creates an optimum combination arriving via the conditioner and/or the heat exchanger of a heater of air streams, providing the fastest warming up or air cooling in salon to the set temperature.
|
Automatic control of distribution of an air stream in modes also is disconnected. |
For the fastest warming up or air cooling in salon include a mode of the closed air circulation (see below) and turn the handle of a regulator of temperature in one of extreme (left or right) provisions, - it is thus established top (32°Ñ) or bottom (17°Ñ) a limit of adjustable temperature. If a regulator of air temperature will turn in one of extreme provisions, the system will work in a constant mode, without being switched off, and warming up/cooling air with the greatest possible efficiency. Thus the system does not supervise the current air temperature in car salon. For inclusion of automatic control it is necessary to transfer the handle to any of intermediate provisions. Value of the chosen temperature will be reflected in the display screen the Chosen temperature will be reflected on in the corresponding field of the screen of the display. At desire on the same field of the screen by means of the OUT TEMP button the indication of the sensor of temperature of external air, - can be deduced at negative value, will work a warning sound signal and color of highlighted indications will change on the white.
|
During parking, and also in some other cases when the sensor of temperature of external air gets to a zone of influence of heat going from an impellent compartment, or it appears under the direct sunshine, highlighted on the display after OUT TEMP button pressing value can correspond to really taking place temperature not quite. |
The fan automatically turns on in cold weather only after the engine worked some time and a heater is ready to heating of air.
By means of the button (4) inclusion/switching off of an economic mode of functioning of the conditioner of air (ESO) is made. This mode can be chosen at low relative humidity of air and allows to reduce some the superfluous fuel consumption caused by functioning of the Ê/Â compressor.
System functioning in a mode of manual control
Nazhimaniye of any of keys, except AUTO, TEMP and ¤ occurs central air exit from an automatic mode return in which is possible only by repeated pressing the AUTO button.
Choice of the direction of distribution of an air stream
Buttons of a choice of the direction of distribution of an air stream
The choice of the direction of distribution of an air stream is carried out by means of the button (1) and reflected in the right bottom corner of the zhidkokristalny display. By means of the specified button can the choice of one of five modes of distribution of air is carried out:
supply of air in the top part of salon;
supply of air in the top part of salon and in foot wells;
supply of air only in foot wells (forward and back);
supply of air in foot wells and on having blown in glasses;
supply of air only on having blown in glasses.
Condensate removal from glasses
For fast removal of condensate from glasses it is necessary to use the button (2), - the fact of inclusion of a mode of removal of condensate proves to be true operation of the control lamp built in in the button (And). Shutdown of a mode is made by repeated pressing the button.
|
At inclusion of a mode of fast removal of condensate there is an automatic shutdown of an economic mode of functioning of system if that was included earlier. |
Inclusion/switching off of a mode of air circulation
The button of inclusion/switching off of a mode of the closed ventilation of air
Inclusion of a mode of air circulation is made by means of the button located to the left of the button of inclusion of a mode of fast removal of condensate.
Choice of a high-speed mode of functioning of the fan
Location of the button of a choice of a high-speed mode of the fan
The choice of a high-speed mode of functioning of the fan is made by means of the button (1). Parameters of the chosen high-speed mode graphically are displayed in the left bottom corner of the display.
Switching off of system of climate control
|
Shutdown of central air is made by means of the OFF button. By pressing this button there is a shutdown of all functions of system, except for possibility of a choice of a high-speed mode of the fan and the direction of distribution of an air stream. |
Audiosystem
General information
As a rule, the audiosystem is not a part of a standard complete set of the car and is established as the additional equipment.
The firm audiosystem provides purity of sounding in all ranges of frequencies, differs simplicity of switching off of favourite radio stations by means of keys of preliminary control, allows to listen to audiocassettes and provides possibility of management with listening of records from the compact discs charged in a cartridge of a CD changer.
Cassette a deck it is supplied with system of a shumopodavleniye of Dolby, automatic detection of installation chrome-dioksidnoy of a magnetic tape and the function of an automatic reversion providing possibility of continuous reproduction of records from both paths of a tape without reinstallation of an audiocassette.
|
The used Dolby system made on the licenses Dolby Laboratories Licensing Corporation. “Dolby”, and also the pictogram in the form of two stylized letters D are the registered trademarks of the Dolby Laboratories Licensing Corporation company. |
Appearance of the control panel entering into a regular complete set of Mitsubishi cars of a stereoradio tape recorder is presented on an illustration.
Stereoradio tape recorder control panel
Sounding inclusion/volume control
At regular connection the audiosystem functions, when the ignition key is in the situation ACC (I) or ON (II). In the first provision of a key a food of auxiliary consumers of the electric power joins, in the second - ignition and a food of all consumers of the electric power is included. Inclusions of an audiosystem it is made at a nazhimaniye way on the push-button PWR/VOL handle. Rotation of the same handle allows to carry out reproduction volume control.
Adjustment of a timbre of sounding (BASS/TREB)
For implementation of a regulriovka of a timbre of sounding in a LF mode of a range (BASS) press the button (13) so that she was nominated from the panel, - button turn clockwise leads to increase in intensity of reproduction of low frequencies, against - to reduction.
To pass to timbre adjustment in (TREB) VCh mode the button it is necessary to extend even more from the panel. Adjustment is made in the similar manner described above.
Having finished adjustment, do not forget to drown again the button in the panel.
Balancing (BAL/FADE)
Balancing of level of sounding between the right and left BAL/lobbies and back (FADE) columns is made by means of the button (14). Press the button so that she was nominated from the panel, - button turn clockwise leads to shift of balance of level to the right, against - to the left.
For transition of implementation of balancing between lobbies and back loudspeakers the button should be extended from the panel even more. Adjustment is made in the similar manner described above.
Having finished adjustment, do not forget to drown again the button in the panel.
Radio receiver control
In any of three ranges (USW1/USW2/MW-LW) the radio receiver allows to make control by three possible ways: manually (TUNE), semi-automatic (SEEK), and settings for previously chosen radio stations, which frequencies are brought in memory of a radio receiver. Choice of a range of frequencies of search of AM (MW-LW) and FM (USW1 and USW2).
Manual control (TUNE function) is made by means of the TUNE/SEEK (18/19) key, - for change of frequency of reception of the tuner towards reduction or increase press on left (>) or right <() a part of a key respectively.
In a mode of semi-automatic control (SEEK function) the radio receiver finds in the current range radio station with a strong signal and is independently adjusted on it. For radio receiver inclusion in a mode of search it is necessary to press left (>) or right <() a part of the TUNE/SEEK key and to hold and hold it pressed during about 0.5 seconds. Radio station search will occur to rather strong signal in bottom or top ïîääèàïàçîíå rather current frequency of control of a radio receiver, depending on on what part of a key the nazhimaniye is made. Search stops, as soon as the receiver finds the first radio station with rather strong signal.
Radio receiver control for previously chosen stations. By means of six buttons (20) marked with numbers from 1 to 6, it is possible to bring in memory of a radio receiver of frequency of favourite radio stations. Each button allows to program one frequency in a radio range of AM (MW-LW) and two frequencies in FM range (on one in each of USW1 and USW2 ranges). To program memory of a radio receiver, execute the following operations:
a) By means of the UML (16) button choose a demanded range of radio frequencies (USW1/USW2 or MW-LW); b) By means of the TUNE/SEEK key adjust a radio receiver on desirable radio station; c) Choose for this radio station one of six buttons of programming of memory, press and hold it until will hear a short sound signal; d) Repeat operations with the first on the third to bring in memory of a radio receiver of frequency of six radio stations; e) Now it is enough to press any of six buttons of programming of memory of a radio receiver that it was automatically adjusted on previously chosen station which frequency of a signal is brought in the corresponding cell of memory.
Frequencies of preliminary settings of a radio receiver are erased from memory at failure (the strong category) or shutdown of the storage battery, and also at extraction of a safety lock of an audiosystem.
System of radio data of RDS
The design of the tuner of an autoradio tape recorder gives opportunity to use the service functions of system of radio data of RDS especially well developed abroad. In RDS system the signal of identification of programs (PI) and the list of the alternative frequencies (AF), transferred by some of the radio stations broadcasting in an ultrashort range of frequencies (FM) is used. At RDS function activization the radio receiver tuner, using a strengthening method another of a set (EON), identifies the stations transferring the same program (on the PI code) and it is automatically recustomized on frequencies from the AF list with the strongest signal. This function allows to listen on distant trips to one and a touch the program without switching of frequencies at an exit from radius of action of the next repeater. In addition RDS renders such services, as a choice of desirable type of accepted information (PTY), interruptions of the current broadcasting for scoring of the spot news and information on a condition on roads (TP), and also restriction of the list of accepted regional radio stations.
Automatic change-over on the chosen program
This function allows to carry out reception of the chosen program of radio station supporting the RDS standard with an automatic choice of the strongest signal from a range of alternative frequencies (AF) without receiver switching when passing considerable distances. For inclusion of a mode press and hold in the drowned condition not less than 2 seconds the UML (16) button, - on the display of the control panel of a radio tape recorder (21) “AF” (27) label will be highlighted. Return of the tuner to a usual mode of reception is made by repeated long pressing the UML button.
Identification of programs (PI)
At reproduction of the frequencies programmed by means of buttons (20) there is a possibility of listening broadcasting with the same identification code (PI). If signal level on the programmed frequency decreases to an inadmissible limit, the tuner carries out an automatic choice of other station of the same network transferring the similar program, - on the screen of the display “REG” (23) label will thus be highlighted.
Choice such as accepted programs (PTY)
In RDS system all broadcasts are sorted according to type of transferred programs (on subjects). Activation of a mode of a choice is made by a nazhimaniye on the PTY (3) button. The choice such as accepted programs is made by means of the TUNE/SEEK button (18/19) of the following list:
1 SPEECH Speech 2 NEWS of News 3 AFFAIRS Business 4 INFO Information programs 5 SPORT Sports programs 6 EDUCATE Educational programs 7 DRAMA Theatrical performances 8 CULTURE Culture 9 SCIENCE Science 10 VARIED Different 11 MUSIC Musical programs 12 POP M Pop music 13 ROCK M Rock music 14 M.O.R. M. Road music 15 LIGHT M Light music 16 CLASSIC Classical music 17 OTHER M Other music
|
At a choice of positions 1 and 11 () search is conducted largely the concepts "Speech" and "Music" |
|
For activation of a mode of a choice of a subject of accepted programs press the PTY (3) button, then short pressing the corresponding I will shift the TUNE/SEEK (18) keys choose a subject from the list, - on the screen of the display the corresponding name will be highlighted. Two seconds later after implementation of a choice search of the transfers answering to set parameters will begin, - in the course of search on the screen “PTY” label will blink. After the demanded radio station will be found, on the display its name will be highlighted.
|
When keeping the TUNE/SEEK button pressed within more than 0.5 seconds the system will try to continue search of the next station which is meeting the requirements of the chosen thematic range. If any station transferring the program of demanded type it will not be found, on the display screen approximately for 5 seconds “EMPTY” inscription will be highlighted, then the receiver will return to reproduction of earlier transferred program. |
|
There is an entering possibility in memory of the tuner to 6 types of programs. The choice such as programs is made with the help the TUNE/SEEK (18/19) key. After the choice will be carried out, press one of six buttons (20) and hold it pressed during not less than 2 seconds. For the period of introduction given in memory of system reproduction of transfer will interrupt, on the display number of the button and the chosen type of the program will be highlighted. The call the type of the program entered into memory is made previously by keeping of the corresponding button pressed during not less than 2 seconds.
|
Shutdown battery/extraction of a safety lock of a radio tape recorder lead to deleting brought in memory of system of data! |
Information for participants of traffic
During listening of the FM-n?a»a?«?a/record programs in audiocassettes or a compact disc the tuner of a radio receiver can make automatic control for reception of transfer of road messages.
For inclusion of function press the TP (4) button, - on the screen of the display “TP” (26) label will be highlighted. If information transfer is made for participants of traffic, on the display screen approximately for 5 seconds “NO RDS” message will be highlighted.
|
If road information is transferred already chosen, or any other station, on the screen approximately for 5 seconds will deduce “TRAF INF” message, then for 2 seconds - frequency of a radio signal, then - the name of the radio station broadcasting road news. If level of loudness of transfer is insufficiently high, the system automatically optimizes it. Upon termination of transfer the receiver will return to reproduction of earlier chosen program. |
Return to a former mode is carried out by repeated pressing the TP button.
Reception of the spot news
|
During listening of the FM-n?a»a?«?a/record programs in audiocassettes or a compact disc the tuner of a radio receiver can make automatic control for reception of the spot news, thus on the screen of the display the warning inscription of "ALARM" is deduced, and level of loudness of reproduction is automatically optimized. Upon termination of transfer of the spot news the receiver automatically comes back to reproduction listened before the program. |
Listening of audiocassettes
General information
Make sure of density of winding of a tape on cartridge coils. Insert the cartridge in a kassetopriyemnik, - reproduction of record will begin automatically even if the radio receiver or the CD player earlier was included. Besides, the mode of reproduction of record from a magnetic tape of cartridge already inserted in a kassetopriyemnik can be included by means of the TAPE (15) button.
When listening the films which have been written down with application of system of a shumopodavleniye of Dolby (with NR mark) the system of suppression of noise can be activated by means of the button (12), - on the screen of the display the corresponding label (30) will be highlighted. Shutdown of system of a shumopodavleniye is made by repeated pressing the same button.
|
The used Dolby system made on the licenses Dolby Laboratories Licensing Corporation. “Dolby”, and also the pictogram in the form of two stylized letters D are the registered trademarks of the Dolby Laboratories Licensing Corporation company. |
Choice of the direction of listening of a magnetic tape
|
The choice of the direction of listening (path) of a magnetic tape is carried out by means of the button (18). The current direction of a prokruchivaniye of a film is displayed on the display screen.
1 Forward 2 Back |
At the film termination switching of the direction of a prokruchivaniye will occur automatically (an "automatic reversion" mode).
The accelerated rewind of a magnetic tape
Film rewind in the corresponding direction is made by means of buttons (9 - forward) and (10 - back) autoradio tape recorder control panels.
By button (18) pressing in the course of rewind of a tape will lead to inclusion of reproduction of record since that moment in which the button was pressed. To similar result will lead pressing in the course of rewind of buttons (9) or (10).
Repetition of reproduction of the chosen fragment
Repetition of reproduction of the pleasant fragment of magnetic recording can be made by means of the RPT (11) button, - on the screen of the display the corresponding message (28) will be highlighted. For cancellation of a mode of repetition once again press the RPT button.
Use of function of automatic search of a music record (APS)
The APS button (7 and 8) allows to find on a magnetic tape from a music record the beginning of the next thing with the admission to 7 music records in a row.
|
For search with rewind forward it is necessary to press the button (8) so many time, how many songs are going to pass, - on the screen of the display serial number of the chosen thing from a point of inclusion of rewind will be highlighted, the tape will quickly be rewound in demanded situation and automatically reproduction will join. Search with scrolling is made in a similar manner, but by means of the button (17) back.
|
For uninterrupted functioning of the APS function of a pause between records on a film should make not less than 4 seconds and to be free from noise. |
|
Stop of reproduction and cartridge extraction
Press the button (5) autoradio tape recorder control panels, - reproduction of magnetic recording will stop, and the cartridge will be âûòîëêíóòà from a nest of a kassetopriyemnik.
Care of a radio tape recorder
In use autoradio tape recorders the magnetic head cassette decks gradually becomes soiled deposits of a dust and particles of a magnetic layer showered from a film. At considerable pollution of a magnetic head quality of a sound at reproduction of records worsens. In view of told, it is necessary regularly, through each 30 business hours decks, to make cleaning of a magnetic head.
The negligent relation to care of a radio tape recorder and violation of the stipulated schedule of cleaning of a magnetic head can lead to a situation when removal of the accumulated deposits by means of the ordinary cleaning cartridge will appear impossible.
The design decks provides possibility of automatic unloading of an audiocassette which for any reasons cannot normally be reproduced. If the cartridge jumps out even prior to the beginning of reproduction, it speaks about its possible damage, it is not necessary to make attempts of repeated loading of such cartridge. There can sometimes be a stop of reproduction of a sound recording, single or double turning on of the mechanism of a reverse decks, or cartridge unloading. Usually similar phenomena occur owing to mechanism jamming, or as a result of unevenness of resistance to rewind of a magnetic tape on cartridge coils. In this case it is necessary to take an audiocassette and manually to waste a tape on some turns of the coil.
Cassette a deck of an autoradio tape recorder it is calculated on use of audiocassettes with duration of record to 100 minutes. Use of more capacious cartridges with a thin magnetic film can lead to refusal decks or film deformations.
Attentively examine an audiocassette before inserting it into a reception window decks. If the magnetic film has a considerable weak point, tighten it, rotating a coil nave in the relevant party by means of a pencil or fingers.
At an otslaivaniye of a label glue it or remove completely. Otherwise, the lagged behind sticker can lead to cartridge jamming in attempt to take it from decks. Do not insert into a reception window decks the pognuty or broken audiocassette.
Do not leave an audiocassette in such places where they are exposed to influence of high temperature or high humidity, for example, on the top shelf of the dashboard or in the most cassette a deck, do not insert the peregrety or overcooled cartridge into a radio tape recorder until its temperature is not normalized.
Do not insert into a reception window cassette decks extraneous subjects.
Listening of compact discs
General information
Elements of management the autoradio tape recorders used at listening of compact discs
The design of a stereosystem allows to carry out listening of compact discs from the CD changer connected to an autoradio tape recorder.
The scheme of placement of elements of management on the panel of a radio tape recorder is shown by a changer on an illustration.
Listening of records from compact discs
Insert a disk into the CD player/changer receiver, - track, that the disk refueled a label up. After disk retraction reproduction will begin with it automatically even if the radio receiver or the tape recorder earlier was included. At the disk filled in a player/changer reproduction inclusion from it is made by means of the button (4) on the autoradio tape recorder panel. The system allows to exercise administration of listening to 10 compact discs filled in a cartridge of a CD changer. The choice of number of a disk is carried out by means of the button (5) (see in the same place). Transition to a mode of listening of a radio receiver or magnetic recording is made by means of the UML and TAPE buttons.
Fast moving on a disk
Fast movings on a disk it is made by means of buttons (8 - back) and (9 - forward). At a button otpuskaniye reproduction will renew.
Search of the beginning of a desirable fragment
Search of the beginning of the necessary fragment of record is carried out by means of buttons (6 - back) and (7 - forward). The button is pressed so many time, how many fragments are required to pass, - on the display the corresponding number will be highlighted.
Repetition of reproduction of the chosen fragment
Repetition of reproduction of the pleasant fragment can be made by means of the RPT (10) button. Switching off of a mode of repetition it is made by repeated pressing the same button.
Inclusion/switching off of a mode of casual sequence of reproduction of paths
The mode of casual sequence of reproduction from a compact disc is activated by means of the RDM (11) button, - on the screen of the display the corresponding message (16) (see in the same place) will be highlighted. For shutdown of function press the button once again.
Security system of an autoradio tape recorder
On the models equipped with similar system the detachment for any reasons of an audiosystem from the power supply leads to its blocking. To unblock system, it is necessary to enter a four-unit code by means of buttons of control of a radio receiver on previously chosen stations. As there are hundreds thousands such combinations, to unblock system, without knowing the correct code, it is almost impossible.
|
At audiosystem installation on the car the owner receives a special card with a code and serial number of a stereosystem. Originators of the real Management insistently advise to store a card in a safe and reliable place. Bring serial number of an audiosystem in a notebook and store it together with other documents out of the car. The new card instead of the lost can be received at firm car repair shops of the Mitsubishi company upon presentation of serial number. |
|
In case of the category or a detachment of the storage battery inevitably there is an audiosystem blocking. In this case at system inclusion on the display of the forward panel of a radio tape recorder the inscription “CODE” (Code) is highlighted. By means of buttons of control enter a demanded four-unit code, - by each pressing the button the corresponding figure of a code will change the value to unit from zero to nine in the closed cycle. |
Having finished code input, press the UML button, - if the code is entered correctly and identified by an audiosystem, it starts to function in a usual mode.
At input of the wrong combination on the display screen for short time “X ERROR” message (where X - serial number of a mistake) which then will be replaced by "CODE" invitation, allowing to start repeated input of a combination of a code will be highlighted. The system allows introduction to three erroneous combinations then on the display the message of "OFF" and activation of an audiosystem is deduced HUNDRED Mitsubishis can be made only in conditions.
Sun-protection peaks
|
Sun-protection peaks provide protection of eyes of the driver / the forward passenger from dazzle by direct sunshine both in front, and sideways. |
|
In a passenger peak the toilet pocket mirror equipped with a movable cover is built in addition in. |
Lighter
The lighter is built in in the panel of facing of a forward ashtray on the central section of furnish of the dashboard and functions only at the included ignition (a key in the situation ON or ASS).
For lighter activation simply drown its button in a reception nest against the stop, - after warming up of a heating element the button will automatically jump out in a starting position.
|
At all do not hold the lighter button in the pressed situation by force. If the lighter button after pressing does not jump out more than 30 seconds later, the car should be driven away on car repair shop for elimination of taking place malfunction. After use do not forget to return the button in a nest (in order to avoid a contamination of the last). |
The reception nest of the lighter can be used for connection of external consumers of the electric power (the pump, the charger for a radio telephone, the vacuum cleaner), calculated on a food in 12 In and with consumption capacity no more than 120 W.
Ashtrays
Forward ashtray
|
The forward ashtray is built in in the central (console) section of furnish of the dashboard. For opening of an ashtray pull it on itself.
And Lock uvula |
To take an ashtray for pro-cleaning extend it outside against the stop, then wring out a lock uvula (And) and liberate from a reception niche.
Back ashtray
|
The back ashtray is built in in a back wall of the central console of the car. For ashtray extraction for pro-cleaning extend it against the stop, wring out a lock uvula and liberate from a reception niche.
And — the Lock uvula |
Digital watch
Hours are built in in the central part of the dashboard and function only at the included ignition (a key in the provisions ON or ASS).
Installation of indications of hours is made by means of control buttons: N - installation of hours, M - installation of minutes, SET - dumping of indications of minutes on a zero.
Ware boxes
On cars of considered models the following ware boxes are provided:
Sedan:
· Main ware box · A box on the central console · Office for sunglasses · Coin box · Door pockets · A tool box (if it is provided)
Versatile person:
· Main ware box · A box on the central console · Office for sunglasses · Coin box · Door pockets
Main ware box
|
The main ware box is located on the right under the dashboard of the car and equipped with the lock. |
When opening box the lamp of illumination placed in it automatically joins.
Boxes on the central console
|
The box has two offices (top and bottom) and takes place in a back part of the central console and is equipped with a cover which in the closed condition plays also a role of the central armrest. For cover opening simply pull its first line up. |
|
Under the bottom of a box one more (bottom) office is located. For opening of the bottom box wring out up a lock uvula and lift a cover bottom of the top box. In a box illumination is provided automatically joining when opening cover. |
|
From the interior of the top cover of a console box the holder of coasters and the adaptation for opening of bottles is located. |
|
In a forward pocket of the central console one more adaptation for opening of bottles is equipped. |
Equipment of a luggage compartment
Top shtorka of a luggage compartment (Versatile person model)
|
Do not put on a shtorka of a luggage compartment heavy subjects. |
|
Pull for edge of a shtorka fastening on springs and fix the last in assembly flutes. |
After liberation from assembly flutes the shtorka will automatically return to the cleaned situation
|
Removal of a shtorka is made by a simple pripodnimaniye of assembly. |
Hooks for fastening of cargo (Versatile person model)
On a floor and on lateral walls of a luggage compartment hooks for cargo fastening are provided.
Hooks are intended for gearing for them rubber tapes or cables by means of which the cargo placed in a luggage compartment fastens.
Luggage grid (Versatile person models)
|
The grid is used for fixing of the car of cargo transported in a luggage compartment and fastens on hooks as is shown in illustrations. |
Tool boxes (Sedan models)
|
Boxes (And) are intended for storage of tools and the elements of subsidiary stock transported in a luggage compartment. The box is equipped with demountable partitions that allows to place in it subjects of various size and a form.
And — Boxes for storage of subjects In — the Rubber fixing tape |
The rubber tape can be used for fixing, for example, a sign of an emergency stop.
The partitions being in boxes, can be removed according to the sizes of stored subjects.
The rubber tape (In) can be used, for example, for storage of a sign of an emergency stop.
|
For fixing of the panel of a box to a floor of a luggage compartment are used a hook of D, fastening to the Page sealant. |
Boxes for transportation of luggage (Versatile person model)
|
Boxes are intended for storage of tools and the elements of subsidiary stock transported in a luggage compartment. The box is equipped with demountable partitions that allows to place in it subjects of various size and a form.
And Rubber fixing tape |
The rubber tape (And) can be used, for example, for storage of a sign of an emergency stop.
|
One more, the box is located the equipped folding cover on the left wall of a luggage compartment. |
Tapes for fastening of the first-aid kit and a sign of an emergency stop (Versatile person model)
|
On the lateral panel of a luggage box tapes for fastening of the first-aid kit and a sign of an emergency stop are provided. |
|
|