Mitsubishi Galant

1990 — 2001 of release

Repair and car operation



Mitsubishi Galant
+ Identification numbers of the car
+ Governing bodies
+ Settings and routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Manual transmission
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of racks and screw springs of a forward suspension bracket
   Regenerative repair of rack-mount assemblies of a forward suspension bracket
   Check of a condition of the top spherical support of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Removal and installation of the top levers of a forward suspension bracket (Galant model of 1994-1998 вып.)
   Check of a condition of the bottom spherical support of a forward suspension bracket
   Removal and installation of the bottom levers of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of rotary fists and assemblies of naves with wheel bearings (a forward suspension bracket)
   Removal and installation of back racks
   Regenerative repair of rack-mount assemblies of a back suspension bracket
   Removal and installation of the top managing directors of levers of a back suspension bracket
   Removal and installation of the bottom managing directors of levers of a back suspension bracket
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of the back stabilizer of cross-section stability
   Adjustment of wheel bearings
   Removal and installation of stupichny assemblies
   Removal and installation of a steering wheel
   Removal and installation of the podrulevy combined switch
   Removal and installation of the switch of management by functioning of screen wipers
   Removal and installation of the cylinder of the lock of ignition
   Removal and installation of the switch of ignition
   Removal and installation of drafts of a steering drive
   Replacement of protective covers of assembly of the steering mechanism
   Removal and installation of the steering mechanism with a manual drive
   Removal and installation of the hydrostrengthened steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Removal and installation of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment


Adjustment of wheel bearings

Mirage models

Replacement of wheel bearings is made assembled with naves!


 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Remove a support and a disk of the brake mechanism / a brake drum (see. Head Brake system).
3. Remove a dustproof cover and tighten a flange nut with effort of 180 H • m.
4. By means of a tsiferblatny measuring instrument of plunzherny type define size axial люфта the wheel bearing / ступичной assemblies. The maximum admissible value makes 0.05 mm.
5. By means of a dynamometer and a cord wound round heads of bolts measure effort of a provorachivaniye of the bearing / ступичной assemblies, - the maximum admissible value makes 19 N.
6. If results any of checks fall outside the limits an admissible range, replace a nave.
7. Establish into place a dustproof cover.
8. Establish a brake disk with a support / a brake drum.
9. Establish a wheel and lower the car on the earth.


The Galant models for 1993 вып.

On the models equipped with disk brake mechanisms of back wheels the naves of tight execution which are not needing adjustment are established. It is provided the description of procedure of adjustment of wheel bearings for models with drum-type back brake mechanisms below.


 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
2. Remove a dustproof cover and give a stupichny nut.
3. Rotating a nave / a brake drum, tighten a nut of the wheel bearing with effort of 27 H • m.
4. Release an adjusting nut for removal of a pretightness of the bearing, then tighten it again with effort of 10 H • m.
5. Block a nut and establish new шплинт.
6. Establish into place a wheel and lower the car on the earth.


The Diamante and Galant models since 1994 вып.

 PERFORMANCE ORDER

By means of a tsiferblatny measuring instrument of plunzherny type define size axial люфта wheel bearings/naves. The maximum admissible value makes 0.05 mm at the lock-nut tightened with demanded effort. Adjustment of bearings on these models is not represented possible, - defective components are subject to replacement.